ACV ACVMax Touch Скачать руководство пользователя страница 9

Страница: 9 / 48

Installer's Handbook (Evo) - 660Y3000 • A

Demand Type

screen menu

Thermostat & Outdoor Curve

– A central heating call from a dry contact switch will enable the appliance and the setpoint will vary with the outdoor tem-

perature for central heating calls.

Thermostat & Setpoint

- A central heating call from a dry contact switch will enable the appliance and the setpoint will be fixed for central heating calls.

Constant & Outd. Curve

- The appliance will maintain setpoint and the central heating circulators will be constantly enabled without an external call from

a dry contact switch. The central heating circulators will be disabled when the outdoor temperature exceeds the Warm Weather Shutdown Temperature

setting. The setpoint will vary with the outdoor temperature for central heating calls.

Constant & Setpoint

- The appliance will maintain setpoint and the central heating circulators will be constantly enabled without an external call from a

dry contact switch. The central heating circulators will be disabled when the outdoor temperature exceeds the Warm Weather Shutdown Temperature

setting. The setpoint will be fixed for central heating calls.

0 - 10V Power Modulation

- This option allows the appliance firing rate to be controlled by an external control system. Based on the control input volt-

age, the appliance will start to operate for heat demand. The CH temperature is limited by the Absolute maximum temperature.

•

0 – 2V appliance is off.

•

2 – 10 V linear power increase from minimum to maximum output.

•

10 – 2 V linear power decrease from maximum to minimum output.

•

2 – 1 V appliance on minimum capacity.

•

1 - 0 V appliance off.

0 - 10V Temp. Modulation

- This option allows the appliance CH temperature to be

controlled by an external control system. Based on the control input voltage, the

appliance will start to operate for a heat demand.

•

0 – 2V appliance is off.

•

2 – 10 V linear temperature increase from minimum (27°C) to maximum (87°C) temperature.

•

10 – 2 V linear temperature decrease from maximum (87°C) to minimum (27°C) temperature.

•

2 – 1 V appliance on minimum temperature.

•

1 - 0 V appliance is off.

CH Settings

Heating Settings

Heating Operation

Enabled

Demand

Thermostat & Setpoint

CH maximum capacity

100%

CH minimum capacity

Abs. Max. CH Setpoint

87°C

CH1 Max. Setpoint

82°C

Demand Type

Thermostat & Outd. Curve

Thermostat & Setpoint

Constant & Outdoor Curve

Constant & Setpoint

0-10 V Power Modulation

0-10 V Temp. Modulation

max

min

tpu

Voltage

DESCRIPTION AND OPERATION

Содержание ACVMax Touch

















































Результаты поиска

Содержание ACVMax Touch

Отзывы:

ACV ACVMax Touch, Руководство по установке, Страница: 9 / 48

Результаты поиска

Содержание ACVMax Touch

Отзывы: