ACV ACVMax Touch Скачать руководство пользователя страница 22

Страница: 22 / 48

Installer's Handbook (Evo) - 660Y3000 • A

The

Ignition Level

parameter allows to change the fan start speed of the appliance.

Touch the

LEFT

RIGHT

soft keys to adjust the settings, then

to validate your selection.

Default

: See table below for the fan speed applicable to each appliance/gas combination

Boiler Settings

Model HeatMaster

Lockout Temp.

221°F [105°C]

Modbus Address

0=BCST

Pump settings

Ignition Level

3750rpm

Mix zone high limit

45°C

Pump Settings

Current Pump Config

Config 16

Preset Pump Config

Flexible Pump Config

Pump PWM minimum

100%

Boiler Settings

Model HeatMaster

Lockout Temp.

221°F [105°C]

Modbus Address

0=BCST

Pump settings

Ignition Level

3750rpm

Mix zone high limit

45°C

Ignition Level

3750rpm

1400rpm

5200rpm

Pump PWM minimum

100%

Natural Gas (G20)

Propane (G31)

HeatMaster / WaterMaster Evo

25 kW

3750 rpm

35 kW

3750 rpm

45 kW

3750 rpm

70 kW

3750 rpm

85 kW

3750 rpm

120 kW

4300 rpm

The

Pump PWM minimum

function allows to adjust the minimum pump setting if the flow in the appli-

ance / system is insufficient at minimum appliance rate.

Touch the

LEFT

RIGHT

soft keys to increase/decrease the value, then

to validate your selection.

Default: 100%

Mix zone high limit

45°C

20°C

80°C

Boiler Settings

Prestige Model

HeatMaster

Lockout Temp.

221°F [105°C]

Modbus Address

0=BCST

Pump settings

Ignition Level

3750rpm

Mix zone high limit

45°C

The

Mix zone high limit

setting allows to limit the maximum temperature in the mixed circuit. The function works like an Overheat Cut-

off Activation of the limit and will cause the appliance to go in fault state (lockout). This setting allows to change the limit temperature

for the mixed circuit. It is based on the CH1 setpoint.

Be aware that for Floor Heating systems this temperature may NOT be adjusted. A higher temperature setting may

damage your floor heating circuit

Touch the

LEFT

RIGHT

soft keys to decrease/increase the temperature value, then

to validate your selection.

Default: 45°C

DESCRIPTION AND OPERATION

Содержание ACVMax Touch

















































Результаты поиска

Содержание ACVMax Touch

Отзывы:

ACV ACVMax Touch, Руководство по установке, Страница: 22 / 48

Результаты поиска

Содержание ACVMax Touch

Отзывы: