Acura 2014 RDX REMOTE CONTROL Скачать руководство пользователя страница 24

Страница: 24 / 25

24 of 25

BII 48865 (1303)

FUNCTION CHECK

Operating Conditions

• The hood is closed

• The shift lever is in park

• Turn the ignition switch off and the key is outside the vehicle

• All doors and tailgate closed and locked

Inspection

Press the engine/command button on the transmitter, and release, within 2 seconds, press the lock/start button on
the transmitter.

The engine should start if all operating conditions are met.

Does the engine start?

Press the engine/command button on the transmitter
and release, within 2 seconds, press the unlock/stop
button. The engine should stop.

Does the engine stop?

After the engine has stopped, start the engine again,
and check that the engine stops after each of the
following conditions:

NOTE: After each test the ignition key must be cycled, or the
driver’s door must be opened and closed.

•

Move the shift lever out of the P position.

•

Unlock or open the doors or the tailgate.

•

Open the hood.

•

Press on the brake pedal.

•

Press the engine start/stop button.

Does the engine stop after each of these tests?

Check that the power windows and the moonroof do not function, and the shift lever does not move to any position
when the engine is started with the transmitter.

Check that the engine does not start under “Operating Conditions” with the key left inside the vehicle.

Start the engine again, press the engine/command button on the transmitter two times, and check the vehicle
condition on the display.

Check the operation of the transmitter when the vehicle is 120 m (400 ft.) away and in direct sight.

Yes - Operation is normal.

No:

• Make sure all “Operating Conditions” are met.

• Check the engine starter harness connections.

• Connect the HDS/MVCI and check for an indicated

failure. (Refer to the appropriate Service Manual for

details.)

Yes - Operation is normal.

No - Check the engine starter harness connections.

Yes - Operation is normal.

No - Check the engine starter harness connections.

B127121H

ENGINE/
COMMAND
BUTTON

UNLOCK/
STOP
BUTTON

RECEPTION
INDICATOR

CHECKING
INDICATOR

ENGINE START
OPERATION

Blinking

ENGINE
RUNNING
INDICATOR

IN-CAR
TEMPERATURE

REMAINING
IDLING TIME

*1 Only on vehicles equipped with the automatic climate control.

This indicator is displayed for some vehicles among them.

LOCK/
START
BUTTON

Содержание 2014 RDX REMOTE CONTROL


























Результаты поиска

Содержание 2014 RDX REMOTE CONTROL

Отзывы:

Похожие инструкции для 2014 RDX REMOTE CONTROL

Бренды по названию

Популярные бренды

Acura 2014 RDX REMOTE CONTROL, Руководство по установке

Результаты поиска

Содержание 2014 RDX REMOTE CONTROL

Отзывы:

Похожие инструкции для 2014 RDX REMOTE CONTROL

Бренды по названию

Популярные бренды