ActronAir BMS MODBUS 485 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 24

background image

Installation and Commissioning Guide

ICUNO-MOD

7

6

Installation and Commissioning Guide ICUNO-MOD

Doc. No. 9590-3013

Ver. 5 200722

ActronAir is constantly seeking ways to improve the design of its products, therefore specifications are subject to change without notice.

Copyright © 2019 Actron Engineering Pty. Ltd.

04.02. Installation for Classic Series 2 (Reverse Cycle - CRA Models)

To install ICUNO-MOD Interface Board into the Outdoor Electrical Panel and to UNO Outdoor Board

Step 1.

Isolate and fit electrical lockout device and TAG to the main circuit breaker for the system you are

working on, before removing the Electrical Panel Cover

.

Step 2. Open Electrical Panel Cover.

Step 3. Test unit with multimeter to ensure there is no power, before starting installation of the BMS card.

Step 4. Use supplied PCB Mounts to mount ICUNO-MOD into correct location.

NOTE

: Location will differ between ActronAir systems.

Step 5. Install BMS ICUNO-MOD as shown below.

Single Phase (10kW - 17kW)

BMS ICUNO-MOD

Three Phase (13kW - 23kW)

BMS ICUNO-MOD

«
...
5
6
7
8
9
...
»

Содержание BMS MODBUS 485

























Отзывы:

Нет отзывов

Похожие инструкции для BMS MODBUS 485

Бренд: TCF Страницы: 19

Бренд: Haier Страницы: 56

Бренд: Panasonic Страницы: 122

Бренд: Eaton Страницы: 11

Бренд: Produal Страницы: 9

Бренд: Thule Страницы: 8

Бренд: Jaypro Sports Страницы: 2

Бренд: Ikan Страницы: 2

Бренд: media-tech Страницы: 13

Бренд: matev Страницы: 23

Бренд: TCL Страницы: 34

Бренд: GROTHE Страницы: 36

Бренд: Chamberlain Страницы: 4

Бренд: Gree Страницы: 86

Бренд: Gira Страницы: 8

Бренд: Subal Страницы: 13

Fit 4-All Music

Бренд: Variphone Страницы: 2

Бренд: Friedrich Страницы: 171

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды