background image

Installation and Commissioning Guide

ICUNO-MOD

 

 

17

  

16

Installation and Commissioning Guide ICUNO-MOD

Doc. No.  9590-3013  

Ver. 5  200722

ActronAir is constantly seeking ways to improve the design of its products, therefore specifications are subject to change without notice.

Copyright © 2019 Actron Engineering Pty. Ltd.

Symptom

Probable Cause

Suggested Resolution

Air Conditioning
Unit won’t operate 
from BMS

Air Conditioner 

Fault Preventing AC 

from operating 

OR

UNO Board 

not configured 

correctly for BMS 

Control

•  An Air Conditioner fault may prevent the unit from operating from a BMS 

command.

•  Or the UNO Outdoor Board may be incorrectly setup for BMS Control.

•  From the unit, check the UNO Board 7-segment display for any Unit Fault Error 

Codes

•  Consult the Air Conditioner unit’s troubleshooting guide to resolve the fault.
•  Confirm that the UNO Outdoor Board is setup for the correct BMS Control 

Mode as per your installed BMS network setup

•  See Section 05 for instructions on configuring UNO Outdoor Board for BMS 

Control.

•  From the BMS Controller, ensure that you are able to read data from the correct 

BMS Registers, and that there are no address base issues.

•  Try reading from Modbus Analogue Register 405 for BMS Card Software Version 
•  If Modbus Register 405 reads a 0, then try read from Modbus Register 406 

instead. If this returns a non-zero value, then plus one offset will need to be 
added to all Modbus registers. 

•  Check for any Air Conditioner operation faults by reading the Alarm Output 

from Modbus Analogue Register 503. If this register is 

1

, then the unit will not 

operate.

•  Check BMS Card to A/C unit communications by reading from Modbus 

Analogue Register 909. If this register reads a 1, then the BMS Card is not 
connected to the A/C unit correctly. 

•  Inspect UNO Outdoor Board and BMS Card for faults 
•  Check the unit fault error code by reading from Modbus Analogue Register 

900.

•  Consult the Air Conditioner unit’s troubleshooting guide to resolve the fault.
•  Once all faults are resolved, Modbus Analogue Register 503 should be cleared, 

indicating that the unit is no longer in a fault condition.

•  Confirm that the UNO Outdoor Board is setup for the correct BMS Control 

Mode by reading the BMS Control Mode from Modbus Analogue Register 505.

•  If operating in Basic BMS Control, then Modbus Analogue Register 505 should 

read 1.

•  If operating in Advanced BMS Control, then Modbus Analogue Register 505 

should read 2.

•  See Section 05 for instructions on configuring UNO Outdoor Board for BMS 

Control.

If the above steps fail to fix the problem. Contact ActronAir Technical Support on 1800 119 229 for further assistance.

Содержание BMS MODBUS 485

























Отзывы: