Actron AutoScanner Plus CP9180 Скачать руководство пользователя страница 9

Страница: 9 / 104

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Safety – v

Safety Precautions

Battery acid is a highly corrosive sulfuric acid.

• Safety goggles and protective gloves must be worn

by the operator and any bystanders.

- Even if your everyday glasses have impact resistant

lenses, they are NOT safety glasses, and may not
provide adequate protection.

• Make sure someone can hear you or is close enough

to provide aid when working near a battery.

• Have plenty of fresh water and soap nearby.

- If battery acid contacts skin, clothing, or eyes, flush

exposed area with soap and water for 10 minutes.
Seek medical help.

• Do not touch eyes while working near battery.

Battery acid can burn eyes and skin.

WARNING

Содержание AutoScanner Plus CP9180








































































































Результаты поиска

Содержание AutoScanner Plus CP9180

Отзывы:

Похожие инструкции для AutoScanner Plus CP9180

Бренды по названию

Популярные бренды

Actron AutoScanner Plus CP9180, Руководство пользователя

Результаты поиска

Содержание AutoScanner Plus CP9180

Отзывы:

Похожие инструкции для AutoScanner Plus CP9180

Бренды по названию

Популярные бренды