Actron AutoScanner Plus CP9180 Скачать руководство пользователя страница 30

Страница: 30 / 104

Using The Scan Tool

3 – 4 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Scan Tool Power UP

✓

Refer to

Scan Tool Does Not Power Up

in section 5

Troubleshooting

on page 5-2 if there are problems.

Internal Battery

✓

ON/OFF

button on Scan Tool turns tool

on and off.

❒

Press and hold

ON/OFF

key for at

least 1 second to turn on Scan Tool.

✓

The Scan Tool will automatically turn off after 1.5 minutes of
inactivity when powered from internal 9V Battery.

✓

When powered from the internal battery, the Scan Tool disables
the display’s backlighting and turns OFF after a period of inactivity.

✓

Each time the Scan Tool is
powered up, voltage of the internal
battery is checked.

❒

If voltage is low, the Low
Battery Symbol (

) displays

on screen.

❒

Replace the battery using
instructions provided in Battery
Replacement.

If the Scan Tool will not be used for an extended
period of time, remove the battery to prevent battery
leakage from damaging the battery compartment.

OBD II Function List

=====================

I/M Readiness
Read Codes
Pending Codes
Erase Codes
State OBD Check
View Data

CAUTION

Содержание AutoScanner Plus CP9180








































































































Результаты поиска

Содержание AutoScanner Plus CP9180

Отзывы:

Похожие инструкции для AutoScanner Plus CP9180

Бренды по названию

Популярные бренды

Actron AutoScanner Plus CP9180, Руководство пользователя

Результаты поиска

Содержание AutoScanner Plus CP9180

Отзывы:

Похожие инструкции для AutoScanner Plus CP9180

Бренды по названию

Популярные бренды