Actron AutoScanner Plus CP9180 Скачать руководство пользователя страница 45

Страница: 45 / 104

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 3 – 19

Using The Scan Tool

✓

When selected data does not exist in the Scan Tool’s memory, a
message informs the user to run the function.

3.Return to

Select Print Data

screen.

•Press

ENTER

Code Lookup

is used to look up definitions of DTCs stored in the Scan

Tool.

✓

The Scan Tool does not require power from the vehicle to perform this
function.

✓

Code Lookup

is available from both the

Main Menu

and

OBD II

Function List.

1. Select

Code Lookup.

•Use

DOWN

arrow

key until

Code Lookup

highlighted.

•Press

ENTER

2.Select a Vehicle

•See

Vehicle Selection

for

details regarding this step

✓

This step is available only if a vehicle has not been selected since
the tool was powered up.

✓

Selecting a vehicle may provide the user with a manufacturer
definition when looking up manufacturer specific codes.

OBD II Function List

=====================

Record Data
Vehicle Information
Modules Present
Review Data
Print Data

Code Lookup

System Setup

Содержание AutoScanner Plus CP9180








































































































Результаты поиска

Содержание AutoScanner Plus CP9180

Отзывы:

Похожие инструкции для AutoScanner Plus CP9180

Бренды по названию

Популярные бренды

Actron AutoScanner Plus CP9180, Руководство пользователя

Результаты поиска

Содержание AutoScanner Plus CP9180

Отзывы:

Похожие инструкции для AutoScanner Plus CP9180

Бренды по названию

Популярные бренды