Actron AutoScanner Plus CP9180 Скачать руководство пользователя страница 58

Страница: 58 / 104

Vehicle Diagnostics

4 – 12 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

4 4

State OBD Check (Emissions)

The

State OBD Check

function is used to display a basic status of the

vehicles OBD system.

❒

Malfunction Indicator Lamp (MIL) Status

❒

Codes Found

❒

I/M Readiness

✓

The

State OBD Check

function has the following areas:

❒

MIL STATUS ON or OFF

❒

Number of Codes Found

❒

Number of Monitors OK

❒

Number of Monitors Inc

❒

Number of Monitors N/A

✓

State OBD Check

should be done with the key on engine running

(KOER) due to showing MIL status.

✓

The number of codes found are

only

Generic OBD II codes and

not

Pending codes.

✓

The number of Monitors that are either OK, INC or NA are

only

Since

DTCs Cleared and

not

This Drive Cycle.

✓

Refer to

Read Codes

and

I/M Monitors

for more detailed information

about the results.

Содержание AutoScanner Plus CP9180








































































































Результаты поиска

Содержание AutoScanner Plus CP9180

Отзывы:

Похожие инструкции для AutoScanner Plus CP9180

Бренды по названию

Популярные бренды

Actron AutoScanner Plus CP9180, Руководство пользователя

Результаты поиска

Содержание AutoScanner Plus CP9180

Отзывы:

Похожие инструкции для AutoScanner Plus CP9180

Бренды по названию

Популярные бренды