background image

ActronAir

 

is constantly seeking ways to improve the design of it’s products, therefore specifications are subject to change without notice.

Copyright © 2017 Actron Engineering Pty. Ltd.

Page 7 of  16

LIFTING THE UNIT

Always observe WH&S regulations for safe & secure lifting 

practices in order to prevent physical injury.  

Suggested lifting procedures are outlined in the next page 

as reference guide to safely lift & transport the unit, however, 

these does not over rule the industry WH&S practices.   

LOCATION

This unit is intended for indoor installation only. 

It is highly 

recommended that this indoor unit and accessories, 

particularly zone barrels, be mounted in the roof cavity.

Mount the unit in a stable and rigid support wherein the 

weight is properly distributed, such as roof joist and rafters. 

Take into consideration the minimum service access 

clearances  provided in the unit drawings. 

Locate the indoor unit away from the areas where noise 

is a critical factor. Use rubber mounting pad (not supplied) 

in order to minimize the transfer of noise & vibration into 

building structures. 

A hanging bracket assembly & rubber grommet (optional on 

other units) are also provided to secure the indoor unit into 

the roof rafters. This installation configuration is most suitable 

for installation that require the unit to be rigidly secured up 

from the roof joist.   

   

CONDENSATE & SAFETY TRAY DRAINAGE

An integrated safety drain tray is provided as a standard 

inclusion to your indoor unit in order to reduce the potential of 

condensate damage to the roof. Drain Kit (optional on some 

units) is provided for the condensate drain to be externally 

trapped from the indoor unit. Suggested condensate 

and safety tray drainage instructions are provided at the 

proceeding page for your reference. 

SUPPLY AIR & RETURN AIR DUCT

The indoor unit is supplied with duct flange as standard in 

order to facilitate the system’s duct connection into the unit. 

Supply and return air duct works must be adequately sized to 

meet the system’s air flow and static pressure requirements. 

Refer to the unit drawing for supply air and return air duct 

dimensions, specific to your requirement.

NOTE: Fit a flexible duct connection in between the unit 

and the duct system, where noise & vibration is a critical 

consideration.

RETURN AIR FILTER 

Air filters must be provided in the return air side of the unit 

in order to maintain the efficiency and prolong the operation 

of the unit. These are also paramount in order to  satisfy 

requirement for a clean & hygienic room condition. Air filters 

must be placed in an easily accessible location for service 

and maintenance.

NOTES:

    1. Air filters are not supplied with the unit as individual air 

        filtration requirements are varied.

    2. Ensure that filters are cleaned / replaced regularly.

SUPPLY AIR & RETURN AIR DUCT (OPTIONAL)

Supply Air plenums and Duct Plates (twin-spigot) are 

available in order to facilitate your duct system connection to 

the indoor unit. The supply air plenums come in 1-way, 2-way 

and 3-way options, which offer a wider solutions to your 

different air distribution requirements.

SPLIT FAN COIL SYSTEM (OPTIONAL ERQ4-19AS)

The Actron Air innovative 2-piece fan coil system provides 

a solution to your difficult and tight roof space installation 

requirement. This versatile system has a separate fan and 

coil sections. Each of the compact and lightweight section 

is simply installed in two separate locations and joined by 

flexible duct system. Air ducts are attached to each section  

of the split fan coil by both of the supply air plenum and the 

twin spigot duct plate.

FAN COIL w/ VERTICAL DISCHARGE (OPTIONAL)

An upright Fan Coil with vertical supply air discharge is 

also available wherein installation applications require the 

placement of the unit down in a closet, basement or garage. 

Please refer to the Technical Catalogue of your indoor unit 

for dimensions, installation details and specifications.

FIELD PIPE CONNECTIONS

Specifications and installation requirements for field 

pipe connections are contained in the Installation & 

Commissioning Guide of the outdoor unit that matches 

your indoor unit. Please refer to this guide and thoroughly 

understand the procedures for safe and correct indoor and 

outdoor connection. 

ELECTRICAL FIELD CONNECTION

The power supply and control communication data to the 

indoor unit are supplied via the outdoor unit. Please refer 

to the wiring diagram supplied with the outdoor unit for 

specifications. 

All electrical work must be performed by a licensed 

electrician and must conform with the wiring diagram and all 

relevant electrical authorities.   

INSTALLATION INSTRUCTIONS

The installation instructions provided below are intended as a guide only and does not supersede the relevant council, 

state and federal codes, regulations and building code standards. Compliance and consultation with the authorities 

having jurisdiction with the installation of this equipment is the responsibility of the installer. Actron Air will not be held 

liable for any damages or costs as a result of the installer’s failure to comply. Please refer to the matching outdoor unit 

Installation & Commissioning Guide for further information and details. 

Содержание ESP PLATINUM ERQ2-14AS

















Отзывы: