安科瑞电气股份有限公司
23
“节温设置”，子菜单下可在线绑定温度传感器，绑定方法为：进入节温设置界面后通过左
右键先选中要绑定的节点，然后按“
Enter
”键，光标会选中“
0x
F
FFF
”，查看传感器上标签，比如
“
FF FF FF FF FF FF 07 E3
”，
ATE400
传感器的标签为“
119071023007E3
”，通过左右键输入“
0x07E3
”，
再按“
Enter
”键确认，光标会定位到节点名称上，完成后按“
SET
”键退出，如果有修改，界面会
提示是否保存修改过的设置，再按“
Enter
”键保存即可。如果传感器为
ATE100/200
且关闭状态请
打开传感器开关。在线绑定方式适合修改个别传感器的配对，多个传感器的配对建议使用配套调试
软件。
（
V1.36
及以上版本支持手动输入
ID
）
.
“
Sensor Setting
”
, we can bind sensor ID online, the method is: enter the submenu and select
node by left or right button, then press
“
Enter
”
,
“
0x
F
FFF
”
will be selected, check the label on the sensor,
like
“
FF FF FF FF FF FF 07 E3
”
, the label of ATE400 is like
“
119071023007e3
”
, input
“
0x07E3
”
by left or right
button, then press
“
Enter
”
button, the cursor will be back to node selected. Press
“
SET
”
and back to last
interface, if modified, prompt information will be show on the screen, press
“
Enter
”
button for confirm. If
sensor type is 2.4GHz, and it is closed
，
turn on the switch. Binding sensor ID online is suit for a few
sensors, use debug software if there are a large number of sensors.
(User can input sensor ID manually if
the version is V1.36 and above).
“节温校准”，子菜单下可校准已绑定传感器的温度，校准方法为：进入校准界面后通过左右
键先选中要校准的节点，然后按“
Enter
”键，光标会选中温度值，修改为当前实际温度值，再按“
Enter
”
键确认（光标会定位到节点名称上），修改完成后按“
SET
”键退出，如果有修改，界面会提示是否
保存修改过的设置，然后再按“
Enter
”键保存即可，按“
SET
”键取消操作。
“
Calibrate
”
, we can calibrate the temperature values of registered sensors, the method is: enter
the submenu and select node by left or right button, then press
“
Enter
”
, the temperature value will be
selected, modify the value to current temperature, then press
“
Enter
”
button (node will be selected),
after all of temperature values have be modified, press
“
SET
”
, if modified, prompt information will be
show on the screen, press
“
Enter
”
button to confirm, press
“
Set
”
button to cancer.
“继电控制”，子菜单下可设置开出模式，模式分为：
“
DO Control
”, we can set the mode of relay output, the
3 modes are:
ON
：设备上电后，继电器常闭触点为断开，常开触点为闭合，适用于手动控制（
After the
device power on, the relay output closing contactor is open, opening contact is close, it is suitable for
manual
）；
OFF
：设备上电后，继电器常闭触点为闭合，常开触点为断开，适用于手动控制（
After the
device power on, the relay output closing contactor is close, opening contact is open, it is suitable for
manual
）；
Def
.
：由内部逻辑控制继电器的闭合或断开（
the status of relay output contactor is depends on
inside software logic
）。
“电量校准”，子菜单下可校准电参量，校准方法为：进入校准界面后通过左右键先选中
