Acom 2S1 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 32

Acom 2S1 Скачать руководство пользователя страница 27

User's Manual | ACOM 2S1 | Automatic XCVR Commutator

June 2022

S e c t i o n SPECIFICATIONS | Page 27 of 32

NOTICE

Before shipping the commutator, you should contact your local dealer first.

Your dealer can have a specific shipment requirement, e.g., a different shipping address.
It is the sole customer's responsibility to ensure the commutator and all accessories are
properly packaged to avoid any shipping damage.

If transporting for diagnostics and repair, you may not need to ship some cables or
accessories. Please, consult with your dealer first.

Prepare the commutator for shipping as described below:

•

Switch off your transceivers;

•

Disconnect

KEY OUT

and

KEY IN

cables;

•

Disconnect

CONTROL A

and

CONTROL B

cables;

•

Disconnect

OUTPUT

cable;

•

Disconnect

INPUT A

and

INPUT B

cables;

•

Pack the commutator and

CONTROL A

/

CONTROL B

cables in its original cardboard carton

(see Section

2.1 Unpacking and Initial Inspection

);

•

Seal the commutator cardboard carton with self-adhesive tape;

•

Now, the commutator is ready for shipment.

Basic shipping insurance is provided by the customer when sending in a commutator -
you can verify the amount covered by the shipping company by looking on their website.
If you are shipping the commutator, full/upgraded coverage is available as a suggested
option.

For alternative shipping instructions, please, contact your local dealer.

«
...
25
26
27
28
29
...
»

Содержание 2S1

































Отзывы:

Нет отзывов