manualshive.com logo in svg

ACKERMANN 16-2040N, Руководство пользователя

Поделиться
Скачать
ACKERMANN 16-2040N Скачать руководство пользователя страница 16

USER MANUAL 16-2040N / 16-2041N / 16-2042N

 Rev. 07/2016

7. FAULTS AND WARNING SIGNALS                                                                                                

 

           

 

 

     

WARNING MESSAGE

POSSIBLE CAUSE

ACTION TO BE TAKEN

CYLINDER LOW

Cylinder pressure at 40 bar

Prepare a replacement cylinder

Cylinder pressure at 20 bar

Change the cylinder immediately

Gas cylinder valve closed

Open the valve

Insufflator high-pressure hose connector 
disconnected

Turn off the device, check CO

2  

intake

and restart the device

OVER-PRESSURIZATION

Sporadic action on pneumoperitoneum

None (if pressure is 5 mmHg greater
than blow-off pressure for more that 3
seconds   the   device  performs   an
external desufflation)

Tubing kinked

Stretch the tubing

TUBING NOT THERE

The tubing is missing

Connect the tubing

The tubing is wrongly connected
(desufflation actuator)

Connect the tubing correctly

CALIBRATION ERROR

The tubing is connected

Disconnect   the   tubing   from
insufflator’s   outlet   connector   for   2
seconds only

REMOVE TUBING

AUTOMATIC TEST not run

Remove   the   tubing   for   2   seconds,
then replace

Fault in tubing detection

Send device for servicing

CO

2 

NOT DETECTED

Gas cylinder valve closed

Open the valve

Insufflator high-pressure hose
disconnected

Connect   the   hose   correctly   to   the
insufflator

SERVICE

Maintenance action essential

Send device for servicing

No power

Fuses damaged

Check and replace the 2.5A UR fuses
if necessary

For any other problem, please contact your nearest after-sales service team or our HQ in Germany.

8. CLEANING / SERVICE / MAINTANCE                                                                           

 

                

 

             

 

       

8.1 CLEANING / DECONTAMINATION 

 

                                                                                                

 

           

 

       

Only instructions created by the personnel responsible for sterilization in each hospital or health
centre must be followed; these instructions will take  precedence over the information contained in
this manual, which is provided for guidance only.
Always disconnect the device’s electrical plug before cleaning it.

After each use:
• discard disposable sterile tubing; do not try to sterilize it
• clean up any possible splashes of liquid on the insufflator by wiping them with a slightly dampened cloth.

The device MUST be decontaminated before it is sent to the after-sales service team.

PAGE 16

 OF 21

Содержание 16-2040N






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды