aci PIM CPN Скачать руководство пользователя страница 42

Страница: 42 / 48

Photoionization Detector Module PIM CPN

User Manual

PIM_CPN - User Manual (en) - 1.08.docx

Analytical Control Instruments GmbH, Volmerstraße 9A, 12489 Berlin, Germany, www.aci-berlin.com

Page 42 of 48

13.1

How To

–

Replace the PID lamp/front isolation/sensor block

Remove cable

Remove the lamp control connector cable from lamp
case.

Remove PID lamp

unscrew the lamp by a slight left twisting motion

Replace front isolation

Remove the old front isolation from the PID sensor block
by using a tweezer, at the notch on front isolation
border.

Place the new front isolation into the PID sensor block
and make sure that the curvature shows to the lamp
side.

Do not bend or touch the front isolation or
measurement chamber with the finger.

Insert PID lamp

Plug the PID lamp with a slight right twisting motion into
the PID sensor block. The last turn will be a little tough
because the O-ring engages.

Connect the lamp control connector cable to the lamp.

Calibrate the device after replace of front isolation or
installation of a new PID lamp.

Содержание PIM CPN

















































Результаты поиска

Содержание PIM CPN

Отзывы:

Похожие инструкции для PIM CPN

Бренды по названию

Популярные бренды

aci PIM CPN, Руководство пользователя

Результаты поиска

Содержание PIM CPN

Отзывы:

Похожие инструкции для PIM CPN

Бренды по названию

Популярные бренды