background image

 

 

Lever Hoists 

PAGE: 13 

Model MLH 

MLH-005 & MLH-010 

 

 

www.ACIHoist.com|© 2021 ACI HOIST. All rights reserved | 1-866-4-A-HOIST 

8.0: TROUBLESHOOTING GUIDE 

Problem 

Possible Causes 

Corrective Action 

Pinion shaft does not return to 

position after free chaining. 

 

1. Wear of the spline section of the 

pinion shaft. 

2. Deformation or damage of the 

return spring. 

3. Mechanism fouled with foreign 

matter such as dirt and dust. 

Replace with new parts. 

Replace with new parts. 

Disassemble and clean. 

Slip caused by ineffective braking. 

1. Worn out friction discs. 

2. Oil on the braking surface. 

3. Incorrect assembly of the brake 

system. 

Replace with new ones. 

Disassemble and clean. 

Assemble correctly. 

Load dropped while lowering. 

1. Damaged friction discs. 

2. Foreign matter in the braking 

system. 

Replace with new ones. 

Disassemble and clean. 

Jammed operating handle. 

Over-tightening of the brake. 

Operate the lever hoist as if lowering 

a load. 

Noises during hoisting and lowering 

operation. 

Wear or deformation of the load 

chain and load sheave. 

Replace with new parts. 

Operating handle becomes difficult 

to operate during lifting or lowering 

operation. 

1. Over-hoisting or over-lowering. 

2. Twist in the load chain causing it to 

get caught between load sheave and 

from the load chain. 

Operate the hoist in opposite 

direction. 

Operate the hoist in opposite 

direction and remove the twist load 

chain guide. 

 

Содержание MLH-005

















Отзывы: