ACF Greenhouses Cross Country Arctic Series Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 52

ACF Greenhouses Cross Country Arctic Series Скачать руководство пользователя страница 37

18. SEALING THE GREENHOUSE

When all the polycarbonate sheets are installed, take a tube of clear silicone sealant and seal all
the panels that fit into the aluminum tracks on the top, the bottom, the inside and the outside.
In this way, you can keep out most of the moisture from the end of the panels. If this sealing
process is not done, water may sit in the bottom and fill the inside of the panels and grow algae.

1. Unscrew the plastic nozzle on the tube of silicone sealant.

2. Cut the top of the tube.

3. Screw on the plastic nozzle again.

4. Cut approximately 1/8” off the end of the plastic

nozzle at a 30-degree angle.

5. Put the tube into the caulking gun. When using

the gun, squeeze the handle slowly.

6. Wherever the polycarbonate sheets are sitting in a

track or aluminum “ ”. Also seal the inside of
the “ ” on the ends and sidewalls because
greenhouse humidity runs down the panels into
the “ ” track.

7. Seal the vents before you slide them into place.

Seal the places where the panels fit into the door
frame bar and the “ ” under the above door
angle.

CAULKING / SEALING

• Seal the door frame bar where the base/sill

meets the door frame.

• Seal the inside of the base/sill

along the perimeter of the
foundation.

Do Not seal the

“ ”

to the base! Any

condensation in the polycarbonate

needs to be allowed out. If the

aluminum

“ ”

is tight against the

base, drill a small weeping hole.

Inside view

Outside View

Roof

– 36 –

C R O S S C O U N T R Y T R I P L E W A L L S E R I E S • G R E E N H O U S E I N S T R U C T I O N S

POL

YCARBONA

TE SHEET

Base

DO
NOT
SEAL

ACF Greenhouses

«
...
35
36
37
38
39
...
»

Содержание Cross Country Arctic Series





















































Отзывы:

Нет отзывов