ACF Greenhouses Cross Country Arctic Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 52

background image

– 31 –

C R O S S C O U N T R Y T R I P L E W A L L S E R I E S • G R E E N H O U S E I N S T R U C T I O N S

15. DOOR INSTALLATION

(Refer to the drawing.)

Take the door and set it inside the door frame. Lift it up as high as

possible on the hinge side and put the screws through the existing holes in the door frame.

Now the door will hang by itself.

Remove the black clip from the “Z” bar and put one screw into the door frame to hold the “Z”
bar. Open the door, take off the clips and put back the screws. Close the door and check that it is
square. If the frame and the door are square, then fasten the “Z” bar to the frame. If not, move
the “Z” bar up or down to square it. If this
is not enough, loosen the bolts in the top
plates and move the frame to make it
square. When it is in place, tighten all the
bolts.

Next install the door handle (see the
instructions inside the box). To install
the door catch angle, slide in two bolts
into the back of the door frame. Bolt on a
small angle (provided with the door
handle). Face the angle towards the door,
line it up with the center of the door handle, and then tighten the two bolts

(see picture to the

right)

. Take the door catch out of the door handle box and screw it on. Close the door and

adjust the door sweep at the bottom of the door to eliminate potential gaps.

NOTE:

There are two types of manufactured doors. The door catch angle on the white door may have to be

turned the opposite way as shown on picture

.

Run a bead of silicone under the angle above the door and against the door frame. Also
silicone the poly beside the door to ensure an airtight seal.

1

1

Door Catch Angle

Z Bar

Z Bar

ACF Greenhouses

«
...
30
31
32
33
34
...
»

Содержание Cross Country Arctic Series





















































Отзывы:

Нет отзывов

Похожие инструкции для Cross Country Arctic Series

Domestic Tunnel 2.36x1.5m

Бренд: Redpath Страницы: 14

Бренд: Palmen Страницы: 31

Бренд: Dancover Страницы: 20

Harmony 6x14 Clear Glazing

Бренд: Palram Страницы: 83

Aquaponics System I Series

Бренд: FarmTek Страницы: 43

Sun Lounge Roof Vent

Бренд: Palram Страницы: 23

Snap & Grow 8'x8'+4' Extension

Бренд: Palram Страницы: 61

Snap & Grow HG6008

Бренд: Palram Страницы: 76

Бренд: GardenMeister Страницы: 50

2X3M MEDIUM CAGE

Бренд: Feel Good Страницы: 7

Growers Supply GrowSpan Gothic Pro 106306D

Бренд: FarmTek Страницы: 53

Бренд: Dancover Страницы: 16

Бренд: Dancover Страницы: 34

Бренд: Winter Gardenz Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды