ACF Greenhouses Cross Country Arctic Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 52

background image

– 16 –

C R O S S C O U N T R Y T R I P L E W A L L S E R I E S • G R E E N H O U S E I N S T R U C T I O N S

E

F

G

H

I

J

2

5.

RIDGE

page 18

For a small greenhouse, you handle the ridge by yourself.
Over 12' long it be easier with 2 people. Set the ridge on top
of the end rafters in the middle of the greenhouse. Push the
end rafter out and drop the ridge down 2" and slide it in-
between as far as it goes. The bolt track in the poly bar lines
up with the punch mark in the ridge. Undo the bolt and slide
it up and fasten it

(See Pic E).

6.

TRUSS ASSEMBLY INSTALLATION

page 19 & 20

7.

PERLIN INSTALLATION

page 22

8.

POLY BAR WITH VENT FRAME SLIDERS

page 23

Each poly bar has a slider with a number on it. This number
will also be marked on the ridge. Slide a bolt in the end of the
poly bar

(angle cut end)

and push it tight against the ridge and

bolt it on.

(see Pic G)

. At the bottom end of the poly bar that

now sits into the gutter, lift up the bar and slide the bolt

(or

use the punch out)

and fasten the bar to the gutter.

(See Pic F).

9.

VENT FRAME BOTTOM SECTION

page 24

The vent frame bottom is now ready to go in between the
poly bars that you have just installed

(See Pic G).

The 2" side

of the angle faces towards the Ridge

(See Pic H).

Move the

bolt up the poly bar and fasten it. Be sure the slider

(on the

bar)

butts tight against the ridge lip

(See Pic I)

.

10. REMAINING POLY BARS

page 25

All remaining poly bars can now be installed. Make sure that
the top is against the ridge. Before you tighten the poly bar on
the gutter, eyeball the gutter to see if it is straight. There is
usually about a 1/8" space between the poly bar and the
gutter.

NOTE:

Fasten the greenhouse base/sill to the foundation using #8 x 1”

screws (if it is on concrete, drill holes using a concrete bit and push the

plastic plugs into the holes). If possible, lift the greenhouse and seal

below the base before fastening the greenhouse to the foundation.

11.

Your greenhouse is now ready for putting on the 1/8" foam
strips. Do not put the foam strips on the base or beside the
door. Only use the foam on the poly bars. Do not put foam
strips on the gutter

(See Page 26).

OPTIONALS

Side vents, intake shutters and exhaust fan installation. See
Appendix B – F.

Aluminum Frame Assembly

& Installation

(contd.)

ACF Greenhouses

«
...
15
16
17
18
19
...
»

Содержание Cross Country Arctic Series





















































Отзывы:

Нет отзывов

Похожие инструкции для Cross Country Arctic Series

Victorian ROOKLEY 14 Series

Бренд: Robinsons Страницы: 40

Бренд: ACD Страницы: 66

Бренд: Backyard Expressions Страницы: 4

Бренд: Dancover Страницы: 14

Бренд: ACD PRESTIGE Страницы: 50

Бренд: Palram Страницы: 59

RAISED BED AND HOOP KIT

Бренд: northern polytunnels Страницы: 5

9x12 Greenhouse Kit

Бренд: Mueller Страницы: 23

Бренд: Holman Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды