ACF Greenhouses Cross Country Arctic Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 52

ACF Greenhouses Cross Country Arctic Series Скачать руководство пользователя страница 10

C R O S S C O U N T R Y T R I P L E W A L L S E R I E S • G R E E N H O U S E I N S T R U C T I O N S

Front Gable End Assembly

Lay out the front pieces into the shape of
an end wall. The doorframe and all poly
bars have a track for the bolts. The track
must face up towards you when you
assemble the gable ends. Slide the bolts in
to the ends or use the notches that are
punched out in the glass bars. Refer to the
line/detail drawings when assembling.
(

the sketches/ drawings/ pictures are viewed

from

inside

the greenhouse pages 13 & 14).

1.

At the top of the doorframe, put on
the doorframe header (which looks
the same as the side pieces). Put the
header

between

the two side pieces

and bolt on the plates (6 holes). The
plates should stick up 1” above the
doorframe. Note how the plates are
put on. Before tightening the bolts,
be sure to square up the doorframe

(see pic A & B)

.

2.

The 1” x 2” angle above the door (50”
long) can now be bolted on. The 1/4”
round holes should be lined up with
the holes in the plates

(see pic C)

.

Each end of the 1” x 2” angle has a
slot punched out to accommodate
the bolt in the upright polybar

(see

pic C)

.

3.

Bolt the bottom plates (4 holes) to
the base/sill and the doorframe sides
using 1/4” x 1/2” stainless steel bolts

(see Pic D & E).

Before tightening the

bolts, be sure that it is square.

(A

greenhouse

with no door drop

– fasten

the plate flush with the bottom of door
frame. A greenhouse

with a door drop

,

measure from the bottom of the
doorframe to the underside of the base
according to the specified distance)

4.

Take the corner post

(angle cut on top)

and bolt it to the base

(see Pic F & G)

.

A

B

C

– 9 –

ACF Greenhouses

«
...
8
9
10
11
12
...
»

Содержание Cross Country Arctic Series





















































Отзывы:

Нет отзывов