![background image](http://html.mh-extra.com/html/acer/veriton-m6610/veriton-m6610_service-manual_2838221136.webp)
Chapter 7
128
2-6:Create a“RAID Ready” System into" RAID 1" with two Hard Drives by ‘Create RAID Volume ’.
Step 1:Install WIN7 OS with one SATA HDD.
Step 2:Shut down the system,then add another two serial ATA hard drives in the system.
Step 3:Boot to OS desktop, open the Intel® Matrix Storage Console.
Step 4:Click on the by‘Create RAID Volume’ to create a RAID volume.
Step 5:Click "Next" at create a RAID volume window.
Step 6:Key the name in "Volume Name" and select "RAID 1" in RAID Level.
Step 7:At least select two HDDs as "Volume Location".
Step 8:Specify Volume Size then press "next".
Step 9:Press "next" to finish setup and start create RAID 1.
Step 10:It may takes half and hours to create RAID 1.After create completely,it will ask to reboot to finish
create RAID 1.
2-7:Create a“RAID Ready” System into" RAID 5" with two Hard Drives by ‘Create RAID Volume ’.
Step 1:Install WIN7 OS with one SATA HDD.
Step 2:Shut down the system,then add another three serial ATA hard drives in the system.
Step 3:Boot to OS desktop, open the Intel® Matrix Storage Console.
Step 4:Click on the by‘Create RAID Volume’ to create a RAID volume.
Step 5:Click "Next" at create a RAID volume window.
Step 6:Key the name in "Volume Name" and select "RAID 5" in RAID Level.
Step 7:At least select three HDDs as "Volume Location".
Step 8:Specify Volume Size then press "next".
Step 9:Press "next" to finish setup and start create RAID 5.
Step 10:It may takes half and hours to create RAID 5.After create completely,it will ask to reboot to finish
create RAID 5.
2-8:Create a“RAID Ready” System into" RAID 10" with two Hard Drives by ‘Create RAID Volume ’.
Step 1:Install WIN7 OS with one SATA HDD.
Step 2:Shut down the system,then add another four serial ATA hard drives in the system.
Step 3:Boot to OS desktop, open the Intel® Matrix Storage Console.
Step 4:Click on the by‘Create RAID Volume’ to create a RAID volume.
Step 5:Click "Next" at create a RAID volume window.
Step 6:Key the name in "Volume Name" and select "RAID 10" in RAID Level.
Step 7:At least select three HDDs as "Volume Location".
Step 8:Specify Volume Size then press "next".
Step 9:Press "next" to finish setup and start create RAID 10.
Step 10:It may takes half and hours to create RAID 10.After create completely,it will ask to reboot to finish
create RAID 10.
Содержание Veriton M6610
