ACD MiniBump Скачать руководство пользователя страница 8

 

 

II. START-UP MINIBUMP SOURCE  

To start the generator, 

press and hold 

the ON/OFF Switch, located in the 

middle front of the instrument, until the GREEN LED turns on, approximately 

3 seconds

.  Release the switch immediately thereafter. 

 

 

The GREEN LED will blink at a rapid rate indicating the number of hours 
of gas remaining in the source (5 blinks indicates 5 hours of life 
remaining). It will then blink at a rate of once a second for approximately 
20 seconds.  Gas will begin to be generated immediately. After 20 
seconds, the green light will stay illuminated and the pump will begin 
running. With a bump source installed, the unit will run for an additional 
20 seconds providing a ‘bump’ of output gas to drive the connected 
sensor into alarm after which both red and green lights will alternate 
indicating that the instrument is purging. It will shut off automatically 
after an additional 25 seconds. Note:  Some sensors have faster 
response times than others.  If the system does not respond to the gas 
within 30 seconds, continue to leave the MiniBump attached to the sensor 
throughout the purge cycle and if needed, run the bump cycle a second 
time. 

 

If the RED LED begins flashing or remains lit continuously it indicates the 
instrument is in either low battery condition or source failure mode.  
Please refer to the section on Non-Normal Operation. 

 

Содержание MiniBump





















Отзывы: