ACD MiniBump Скачать руководство пользователя страница 14

 

13 

 

VIII. MAINTENANCE 

The MiniBump instrument is designed to operate at 0.5 liters per minute 
flow rate. For most accurate calibration when using a MiniCal source, the 
flow should be checked and adjusted if necessary. Check the flow using 
a volumetric flow meter connected directly to the output of the 
instrument. 
 
 If the flow needs to be changed simply adjust the flow control 
potentiometer until the correct reading is obtained. To access the 
potentiometer simply remove the top cover of the instrument by pulling 
up on the sides and the two halves will come apart exposing the internal 
workings of the product. Replace the top cover and you are ready to 
calibrate.   
 
Changes in altitude and temperature can cause changes in air density, 
thus affecting the output of the MiniCal source. The output was calibrated 
to STP (standard temperature and pressure) of sea level and 20 °C.  To 
compensate for differences in altitude or temperature from STP, the 
following tables should be utilized: 
 
Note:  Altitude and Temperature are cumulative, i.e., you must correct for 
both factors to obtain the most accurate calibration. 
  
 Altitude Correction Table       

Temperature Correction Table    

Altitude      corrected output    Temperature corrected output 
(in feet)       (multiply by)  

( ° C )    

(multiply by) 

 

   
0          

1.000      

-30               

0.829      

1000    

1.038      

-20               

0.863     

2000    

1.076      

-10               

0.898      

3000    

1.116      

   0               

0.932     

4000    

1.158      

 10               

0.966      

5000    

1.202       

 20               

1.000      

6000    

1.248       

 30               

1.034        

 40               

1.068       

 50               

1.102 

 

(5 PPM @ 3000 feet and 0 C = 5 x 1.116 x .932 = 5.2 PPM actual output) 

        

 

ON/OFF Switch 

The ON/OFF Switch is activated through the front membrane panel.  It is a 

Содержание MiniBump





















Отзывы: