Abit KD7-B Скачать руководство пользователя страница 64

Страница: 64 / 112

3-20

Chapter 3

3F8/IRQ4

2F8/IRQ3

3E8/IRQ4

2E8/IRQ3

AUTO. The default setting is

2F8/IRQ3

Onboard IR Function:

Three options are available: IrDA (HPSIR) mode

ASK IR (Amplitude Shift

Keyed IR) mode

Disabled. The default setting is

Disabled

RxD , TxD Active:

Four options are available: Hi, Hi

Hi, Lo

Lo, Hi

Lo, Lo. The default setting

Hi, Lo

. Set IR transmission/reception polarity as High or Low.

IR Transmission Delay:

Two options are available: Enabled and Disabled. The default setting is

Enabled

. Set IR transmission delays 4 character-time (40 bit-time) when SIR is changed from RX mode

to TX mode.

UR2 Duplex Mode:

Two options are available: Full and Half. The default setting is

Half

. This item lets

you choose the operation mode for your IR KIT. Some IR device only can work at half duplex mode.
Refer to your IR KIT user's guide to find out which setting is correct.

Use IR Pins:

Two options are available: RxD2, TxD2 and IR-Rx2Tx2. The default setting is

IR-Rx2Tx2

If you choose

RxD2, TxD2

your motherboard must support a COM port IR KIT connection. Otherwise,

you can only choose the

IR-Rx2Tx2

to use the IR header on your motherboard to connect your IR KIT.

Please use the default setting.

Onboard Parallel Port:

Sets the I/O address and IRQ of the onboard parallel port. Four options are available: Disable

378/IRQ7

278/IRQ5

3BC/IRQ7. Default setting is

378/IRQ7

Parallel Port Mode:

Four options are available: SPP

EPP

ECP

ECP+EPP. The default setting

ECP+EPP

mode.

EPP Mode Select:

Two options are available: EPP1.7

EPP1.9. The default setting is

EPP 1.7

. When

the mode selected for the parallel port mode is EPP, the two EPP version options are available.

ECP Mode Use DMA:

Two options are available: 1

3. The default setting is

. When the mode

selected for the parallel port mode is ECP, the DMA channel selected can be Channel 1 or Channel 3.

Back to Integrated Peripherals Setup Menu:

Onboard PCI Device:

Press <Enter> key to enter the Onboard PCI Device menu.

KD7 Series

Содержание KD7-B

















































































































Результаты поиска

Содержание KD7-B

Отзывы:

Похожие инструкции для KD7-B

Бренды по названию

Популярные бренды

Abit KD7-B, Руководство пользователя

Результаты поиска

Содержание KD7-B

Отзывы:

Похожие инструкции для KD7-B

Бренды по названию

Популярные бренды