background image

 

EN - 4

3 Safety instructions

Welding torch ERGO

3 Safety instructions

The attached safety instructions must be observed.

3.1 Warnings

In these operating instructions, potentially hazardous work steps are preceded 
by the following warnings. Arranged in descending order of danger, they 
mean:

3.2 Emergency information

In the event of an emergency, immediately disconnect the following supplies:

• Electricity, compressed air, shielding gas

Further measures can be found in the operating instructions for the power 
source or the documentation for other peripheral devices.

Standard length L 

3.00 m, 4.00 m, 5.00 m

Coolant connection

Plug-in nipple, nom. diam. 5

Cooling unit power

Min. 800 W

Control lead

2-core

Tab. 4

Cable assembly B

DANGER

Describes an imminent threatening danger. If not avoided, it will result in 
fatal or extremely critical injuries.

WARNING

Describes a potentially dangerous situation. If not avoided, it may result in 
serious injuries.

CAUTION

Describes a potentially harmful situation. If not avoided, it may result in slight 
or minor injuries.

NOTICE

Describes the risk of impairing work results or potential material damage to 
the equipment.

Содержание ERGO Series













Отзывы: