ABB TZIDC-110 Скачать руководство пользователя страница 9

Страница: 9 / 44

Installing and commissioning

41/18-77 EN

Installing and commissioning

3.1.2 Operating conditions at the installation site

Ambient temperature:

-40 ... +85 °C (-40 ... +185 °F)

Relative humidity

< 75% (95% for a short time), non-condensing
Observe the specifications for protection class
IP65 / NEMA 4X

Explosion protection:

Observe the specifications in the certificate, see section
“Certificates” on page 29.

Mounting position:

any orientation allowed, provided that the splash guard
cap is in place, see section “Mounting the splash guard
cap” on page 15.

3.1.3 Mounting to linear actuators

A special attachment kit is available for mounting the positioner to a linear actuator
according to DIN/IEC 534 (lateral mounting to NAMUR) comprising the following parts:

Tools required:

Wrench 10 mm/13 mm
Allen key 4 mm

• Lever (1.0) w. follower

pin, for 10...35 mm or
25...90 mm actuator
stroke

• Follower guide (2.0)

with two screws (2.1)
and clamp plates (2.2)

• Angle bracket (3.0)

with two screws (3.1),
two spring washers
(3.2), and two plain
washers (3.3)

• Screw (3.4) and plain

washer (3.5) for
mounting to cast iron
yoke

• Two U-bolts (3.7),

each with two nuts
(3.8), two spring
washers (3.9), and
two plain washers
(3.10) for mounting to
columnar yoke

Before installing check to ensure that the specifications in terms of safety
and control applicable to the TZID-C110 will not be exceeded.

Warning

3.4

3.5

3.7

3.10

3.8

3.1 3.2 3.3

3.0

2.1

2.2

2.0

1.0

3.9

Содержание TZIDC-110













































Результаты поиска

Содержание TZIDC-110

Отзывы:

Бренды по названию

Популярные бренды

ABB TZIDC-110, Краткое руководство

Результаты поиска

Содержание TZIDC-110

Отзывы:

Бренды по названию

Популярные бренды