manualshive.com logo in svg

ABB TZIDC-110, Краткое руководство

Поделиться
Скачать
ABB TZIDC-110 Скачать руководство пользователя страница 6

Safety and precautions

2

Safety and precautions

41/18-77 EN

1.2 Explanation of warning signs and notes

Important information has been marked and emphasized with the following symbols in
these operating instructions:  

1.3 Notes on electrical and pneumatic safety

  

1.4 Proper use

The TZID-C110 positioner 

is an electro-pneumatic valve positioner for use with pneu-

matic linear and rotary actuators

.

The device may only be used for the applications listed in these operating instructions
and in the relevant data sheet (if available).

This symbol is printed next to warnings indicating a direct endangerment of a 
person’s health or life. Also, major property damage may occur.

Warning

If the safety notes marked with this symbol are not observed, minor personal 
injuries and property damage may result.

Caution

This symbol is printed next to notes containing important informationen pertai-
ning to your TZID-C110 or its operation.

•

Only qualified persons may mount, electrically and pneumatically connect,
and commission the TZID-C110 positioner.

•

Ensure the electrical safety of all feeding devices.

•

When connecting the electrical wiring, observe the specifications according
to chapter  4 "Technical data".

•

For the electrical installation of ex-protected devices, observe all national
regulations, DIN/VDE directives, especially VDE 0165, the directives for
explosion protection, and the specifications in the EC type examination cer-
tificates (see chapter “Certificates” on page 29 of this manual).

•

Do not use the internal communication interfaces LKS or X5 on the printed
circuit board if the positioner is installed in the hazardous area.

•

Observe the safety instructions of the pneumatic actuators when mounting
and commissioning the devices. There is danger of injuries due to the high
displacement forces of the actuators.

Warning

Содержание TZIDC-110













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды