background image

HE.17454 / TA04928   D   Page 4 of 12

Inspect tool and dies before use. Replace any worn or 
damaged parts. A damaged or improperly assembled 
tool can break and strike nearby personnel. 

Failure to observe this warning could result in severe 
injury or death.

•  Allow approximately 3 to 5 minutes of time to cool 

down as tool automatically switches off when it 

gets too hot.

•  Do not secure this tool in a vise. This tool is 

designed for hand-held operation.

•  This tool may be used in damp or wet environ-

ments; however, air-drying is recommended before 

use if the tool becomes soaked. Damage may 

result when the tool is operated prior to thorough 

drying when electrical components are soaked.

•  Use this tool for the manufacturer’s intended 

purpose only. 

Failure to observe these precautions may result in 

injury or property damage.

Do not allow anything to contact the battery 

terminals.

•  Do not immerse the batteries in liquid. 

Liquid may create a short circuit and 

damage the battery. If batteries are 

immersed, contact your service center for 

proper handling.

•  Do not place the battery into a pocket, tool 

pouch, or tool box with conductive objects. 

Conductive objects may create a short 

circuit and damage the battery.

•  Do not place a battery on moist ground or 

grass. Moisture may create a short circuit 

and damage the battery.

Failure to observe these precautions may 

result in injury or property damage.

•  Do not store the battery at more than 122 °F (50 °C) 

or less than -4 °F (-20 °C). Damage to the battery 
can result.

•  Do not use another manufacturer’s charger. Other 

manufacturers’ chargers may overcharge and 
damage the battery.

•  Do not attempt to open the battery. It contains no 

user-serviceable parts.

Failure to observe these precautions may result in 
injury or property damage.

Do not perform any service or maintenance other 
than as described in this manual. Injury or 
damage to the tool may result.
Failure to observe this precaution may result in 
injury and property damage.

Note: Keep all decals clean and legible, and replace 
when necessary.

CAUTION

CAUTION

CAUTION

CAUTION

WARNING

Содержание Thomas&Betts BAT22-6NV2













Отзывы: