background image

TROUBLESHOOTING

3.2

Problem

Possible Cause

Probable Remedy

Tool is inoperative.

Continuous use causes tool to become too hot 

and automatically switch off.

Allow approximately 3 to 5 minutes of 

time to cool down.

Dirt, contaminants, etc., in jaw area of tool.

Clean tool.

Tool components worn or damaged.

Motor is inoperative.

Return tool to Thomas & Betts Service 

Center.

For parts and service, contact Thomas & Betts Tool Service center at 1-800-284-TOOL (8665).

Return tool to Thomas & Betts Service 

Center.

LED glows for 20 seconds.

Low or uncharged battery.

Try known charged battery. Inoperative 

battery may be discharged or may have 

reached life expectancy.

Broken switch components.

Battery charge low.

Charge or replace battery.

Troubleshooting

Before You Begin

1.   Make sure that the battery is charged. 

Recheck the battery after several minutes to 
make sure the battery is holding its charge.

2.   Use a 

nonflammable 

contact cleaner or 

pencil eraser to clean the electrical contacts 
on the battery and tool.

3.   Reinstall the battery and check the tool again.

HE.17454 / TA04928  D   Page 9 of 12

3.0

OPERATING INSTRUCTIONS

Daily

Before use:

1. Inspect the tool for wear.
2. Inspect the tool for damage, such as cracks, 

gouges or chips.

After use:

1. Use a damp cloth and mild detergent to clean the 

housing. Allow the housing to dry.

2. Place the tool in the carrying case and store in a 

cool, dry place.

3. If necessary, recharge the batteries. Refer to the 

instructions supplied with the battery charger.

Monthly

Thoroughly clean all surfaces.

Annually or After 10,000 Crimps:

Return the tool to an authorized Thomas & Betts 
service center for inspection.

Wear eye protection when operating 
or servicing this tool. 
Failure to wear eye protection could 
result in serious eye injury from 
flying debris.

Do not use solvents or flammable 

liquids to clean the tool body. 

Solvents or flammable liquids could 

ignite and cause serious injury or 

property damage.

Pinch points:

•  Remove battery before changing 

dies, adapters, or jaws.

•  Keep hands away from the 

crimping tool head when crimping.

Failure to observe these warnings 

could result in severe injury or 

death.

MAINTENANCE

3.1

Содержание Thomas&Betts BAT22-6NV2













Отзывы: