background image

CAUTION

•    Do not place the tool in a vise. The crimping tool is designed for hand-held operation.

•    This tool may be used in damp or wet environments; however, we recommend air-drying the tool before use if it because soaked.

•    Use this tool for manufacturer’s intended purpose only.

FAILURE TO OBSERVE THESE PRECAUTIONS MAY RESULT IN INJURY OR PROPERTY DAMAGE.

HE.17454 / TA04928  D   Page 8 of 12

To prepare cable follow the lug manufacturer’s instructions for appropriate cable strip length.

INSTALLING DIES

2.3

BAT22-6NV2 Die Ordering Information

CAT. NO.

DESCRIPTION

DIE2001

Insulated 22-10 AWG Sta-Kon

® 

Terminals

DIE2002

Non-insulated 22-10 AWG Sta-Kon

®

 and Spec-Kon

®

 Terminals

DIE2005

Non-insulated 16-6 AWG Sta-Kon

®

 and Spec-Kon

®

 Terminals

DIE2007

Insulated 8-6 AWG Sta-Kon

® 

Terminals

DIE2500

Insulated 22-10 AWG Spec-Kon

®

 Terminals

TABLE 1

CAUTION

The largest nest must be positioned away from the open 

side of the crimping head, closest to the head itself.  

Failure to do so will result in premature head failure.

1.  Select the proper die set for the intended crimping 

operation, see Table 1.

2.  Remove screw, washer, and die mounting pins from 

the crimping head.

3.  Extend the ram partially by momentarily pulling the 

trigger to access the screw, washer, and pins in the 
ram, and remove.

4.  Insert one die half into the partially extended ram. 

Install the 13mm pins**, screw and washer through the 
ram mounting holes and the die half. Tighten screw 
snugly. Retract ram fully by depressing retract button.

5.  Insert remaining die half into the crimping head, and 

install with 18mm pins**, screw and washer. Tighten 
screw snugly.
** DIE2001, DIE2500 do not use die mounting pins.        
When installing the dies, proceed as described above 
but do not tighten screws fully. After die set is in place, 
ensure dies are properly aligned and extend the ram 
until the dies engage under some pressure. 
Tighten screws snugly.

CRIMPING CABLE

2.4

1.  Insert the properly assembled connector into the 

crimping head.

2.  Pull the trigger to make the crimp.

3.  Hold the trigger down until the crimping tool 

achieves pressure relief, which is accompanied by an 

audible “pop”. Release the trigger. 

4.  The crimping tool returns automatically.

5.  Position the crimping tool for the next crimp. Repeat 

Steps 2 and 3 for the next crimp (see Figure 1).

Sta-Kon

®

 Terminals

One crimp required.

Sta-Kon

®

 Splice

Two crimps required, one 
crimp on each side.

Crimp

Non Insulated

Insulated

Non Insulated

Insulated

FIGURE 2

Crimp

Crimp

Crimp

Crimp

Crimp

NOTE: 

If it is necessary to retract the ram before a crimping 

cycle is complete, push the retract button which will result 

in the complete retraction of the ram.

Keep hands away from the crimping head 
when crimping. Failure to observe this 
warning could result in severe injury.

WARNING

Содержание Thomas&Betts BAT22-6NV2













Отзывы: