ABB SACE Emax 2 E2.2 Скачать руководство пользователя страница 52

Страница: 52 / 56

ABB | SACE Emax 2

Putting into service and maintenance

2 - Identification of alarms or failures

Continued from the previous page

Faults

Possible causes

Suggestions

The circuit-breaker
doesn't open when the
opening coil is powered

The operating mechanism is
blocked

Contact ABB

The power supply voltage of the
auxiliary circuits is too low

Measure the voltage: it should not
be lower than 85 % of the rated
voltage of the coil

The power supply voltage is
different from that indicated on the
rating plate

Use the correct voltage

The cables of the coil are not
inserted correctly in the terminals

Make sure there is continuity
between cable and terminal and if
necessary reconnect the cables of
the coil to the terminals

The connections of the power
supply circuit are wrong

Check the connections using the
relevant wiring diagram

The opening coil is damaged

Replace the coil

The circuit-breaker
doesn't open despite
the command of the
undervoltage coil

The operating mechanism is
blocked

Perform the opening operation
manually; if the fault persists
contact ABB

It is not possible to
charge the closing
springs by means of the
manual charging lever

The operating mechanism is
blocked

Contact ABB

It is not possible to
charge the closing
springs by means of the
gearmotor

The cables of the gearmotor are not
inserted correctly in the terminals

Make sure there is continuity
between cable and terminal and if
necessary reconnect the cables of
the gearmotor to the terminals

The connections of the power
supply circuit are wrong

Check the connections using the
relevant wiring diagram

The circuit-breaker is in
disconnected position

Switch the circuit-breaker to the
test or connected position

The gearmotor protection internal
fuse has tripped

Replace the fuse

The gearmotor is damaged

Replace the gearmotor

It is not possible to
press the button in
order to insert the
racking out crank
handle

The circuit-breaker is closed

Press the opening pushbutton in
order to allow the insertion of the
crank with the circuit-breaker open

It is not possible to
insert the moving part
in the fixed part

The racking-in/racking-out
operation is not performed
correctly

See chapters "Circuit breaker
racking-in/racking-out operations"
on pages18 See the document
1SDH002013A1001

The moving part is incompatible
with the fixed part

Check the compatibility between
the moving part and the fixed part

It is not possible to lock
the circuit-breaker in
the open position

The opening pushbutton is not
being pressed

Press the opening pushbutton and
activate the lock

The lock in open position is
defective

Contact ABB

It is not possible to
perform the trip test

Trip coil is not connected properly

Check Trip coil connection and
messages on display

CB trip signal has not been reset

Press the reset pushbutton

The busbar current is greater than
zero

Correct operating condition.

Continued on the next page

Содержание SACE Emax 2 E2.2

























































Результаты поиска

Содержание SACE Emax 2 E2.2

Отзывы:

Похожие инструкции для SACE Emax 2 E2.2

Бренды по названию

Популярные бренды

ABB SACE Emax 2 E2.2, Инструкции по установке, эксплуатации и обслуживанию для установщика и пользователя

Результаты поиска

Содержание SACE Emax 2 E2.2

Отзывы:

Похожие инструкции для SACE Emax 2 E2.2

Бренды по названию

Популярные бренды