background image

ABB | SACE Emax 2

Management operations

4 - Environmental conditions

30 | © 2023 ABB |  1SDH001000R0002 - ECN000297030

>690V version IEC circuit-

breakers

>690V disconnectors and circuit-breakers are available in the following configurations:

Circuit-breaker

Voltage

Version

E2.2/E9/E10

800/900/1000 V

F-W

E4.2/E9/E10/E12

800/900/1000/1150/1200 V

F-W

E6.2/E9

800/900 V

F-W

Insulating protections are mandatory for >690 V fixed versions of E2.2, E4.2 and E6.2.
Details about assembling insulating protections are available at http://www.abb.com/abblibrary/
DownloadCenter/, especially in the kit sheet 

1SDH001000R0746

.

Grounding

The circuit-breakers in fixed version and the fixed part of withdrawable circuit-breakers are equipped with 
a screw for the ground connection.
The connection must be implemented by means of a conductor of suitable cross-section according to the 
IEC 61439-1 Standard.
Clean and degrease the area around the screw before making the connection.
After assembly of the conductor, tighten the screw with a torque of 2 N m - 17.7 lb in.
Alternatively, no connection will be required if circuit-breaker frame continuity with the switchgear 
earthing is provided by the metal contact (support) between the circuit-breaker and the metal structure 
of the switchgear (or a part of the protection circuit) (as long as there are no insulating panels between 
the circuit-breaker and the metal frame of the switchgear).

Figure 74 - Fixed version

Figure 75 - Withdrawable

 

Содержание SACE Emax 2 E2.2

























































Отзывы: