Table 2:
Binary inputs
IEC61850 LN.DO.DA
AFL-Common SA name
IEC61850 LN Desc, DO Desc, DAName
Value
Binary signal transfer supervision
BSTGGIO1.Alm1.stVal
BSTGGIO1.SEND_SIG_A
Send signal alarm, stVal
1=Send alarm
BSTGGIO1.Alm2.stVal
BSTGGIO1.RECV_SIG_A
Receive signal alarm, stVal
1=Receive alarm
Circuit breaker related signals (
CB pos is found in AI)
CBCILO1.EnaCls.stVal
CBXCBR1.ENA_OPEN
CBXCBR1, ENA_CLOSE, stVal
1 = Close enabled
CBCILO1.EnaOpn.stVal
CBXCBR1.ENA_CLOSE
CBXCBR1, ENA_OPEN, stVal
1 = Open enabled
CBCILO1.ItlByPss.stVal
CBXCBR1.ITL_BYPASS
CBXCBR1, ITL_BYPASS, stVal
1 = Interlocking bypassed
CBCSWI1.Pos.stSeld
CBXCBR1.SELECTED
CBXCBR1, Switch, general, stSeld
1 = CB control selected
CBXCBR1.BlkCls.stVal
CBXCBR1.BLK_CLOSE
CBXCBR1, Block closing, stVal
1 = Close blocked
CBXCBR1.BlkOpn.stVal
CBXCBR1.BLK_OPEN
CBXCBR1, Block opening, stVal
1 = Open blocked
Circuit breaker condition monitoring
CCBRBRF1.OpEx.general
CCBRBRF1.TRBU
CCBRBRF1, Breaker failure trip (external trip), general
1 = Breaker failure trip
CCBRBRF1.OpIn.general
CCBRBRF1.TRRET
CCBRBRF1, Operate, retrip (internal trip), general
1 = Operate, re-trip
CCBRBRF1.Str.general
CCBRBRF1.CB_FAULT_AL
CCBRBRF1, Delayed CB failure alarm, general
1 = Start, timer running
Current circuit supervision
CCRDIF1.Alm.stVal
CCRDIF1.ALARM
CCRDIF1, Alarm, stVal
1 = Alarm
CCRDIF1.Op.general
CCRDIF1.FAIL
CCRDIF1, Detection of current circuit failure, general
1 = Failure
Three-phase current limit supervision
CMMXU1.HiAlm.stVal
CMMXU1.HIGH_ALARM
CMMXU1, High alarm, stVal
1 = High alarm
CMMXU1.HiWrn.stVal
CMMXU1.HIGH_WARING
CMMXU1, High warning, stVal
1 = High warning
CMMXU1.LoAlm.stVal
CMMXU1.LOW_ALARM
CMMXU1, Low alarm, stVal
1 = Low alarm
CMMXU1.LoWrn.stVal
CMMXU1.LOW_WARING
CMMXU1, Low warning, stVal
1 = Low warning
Autorecloser signals
DARREC1.ActRec.stVal
DAAREC1.ACTIVE
DARREC1, Active reclose status, stVal
1=Reclose active
DARREC1.AROn.stVal
DARREC1.AR_ON
DARREC1, AR switched On, stVal
1=AR switched On
DARREC1.CBManCls.stVal
DARREC1.MAN_CB_CL
DARREC1, CB manually closed, stVal
1=CB manually closed
DARREC1.FrqOpAlm.stVal
DARREC1.FRQ_OP_ALM
DARREC1, Frequent operation counter alarm, stVal
1=Frequent operation alarm
DARREC1.LO.stVal
DARREC1.LOCKED
DARREC1, Lockout status, stVal
1=Lockout
DARREC1.Op.general
DARREC1.CLOSE_CB
DARREC1, Operate (close command to XCBR), general
1=Close command to CB
DARREC1.OpOpn.general
DARREC1.OPEN_CB
DARREC1, Operate (open command to XCBR), general
1=Open command to CB
DARREC1.PrgCutOut.stVal
DARREC1.CUTOUT_INPRO
DARREC1, Cutout time in progress, stVal
1=Cutout time in progress
DARREC1.PrgDsr.stVal
DARREC1.DISCR_INPRO
DARREC1, Discrimination time in progress, stVal
1=Discr. time in progress
DARREC1.PrgRec.stVal
DARREC1.INPRO
DARREC1, In progress status, stVal
1=In progress
DARREC1.PrgRec1.stVal
DARREC1.INPRO_1
DARREC1, In progress 1st reclose, stVal
1=In progress
DARREC1.PrgRec2.stVal
DARREC1.INPRO_2
DARREC1, In progress 2nd reclose, stVal
1=In progress
DARREC1.PrgRec3.stVal
DARREC1.INPRO_3
DARREC1, In progress 3rd reclose, stVal
1=In progress
DARREC1.PrgRec4.stVal
DARREC1.INPRO_4
DARREC1, In progress 4th reclose, stVal
1=In progress
DARREC1.PrgRec5.stVal
DARREC1.INPRO_5
DARREC1, In progress 5th reclose, stVal
1=In progress
Table continues on next page
1MRS756879 A
Section 2
DNP3 data mappings
RED615
11
Point List Manual
