ABB OTAC-01 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 19

background image

2

Safety

Safety

WARNING!

All electrical installation and maintenance work on the drive

should be carried out by qualified electricians only.

WARNING!

The drive and adjoining equipment must be properly

grounded.

WARNING!

Do not attempt any work on a powered drive. After

switching off the mains, always allow the intermediate circuit capacitors
5 minutes to discharge before working on the drive, the motor or the
motor cable. It is good practice to check (with a voltage indicating
instrument) that the drive is in fact discharged before beginning work.

WARNING!

The motor cable terminals of the drive are at a dangerously

high voltage when mains power is applied, regardless of motor
operation.

WARNING!

There can be dangerous voltages inside the drive from

external control circuits even when the drive mains power is shut off.
Exercise appropriate care when working on the unit. Neglecting these
instructions can cause physical injury or death.

Use of Warnings and Notes

There are two types of safety instructions throughout this manual:

• Notes draw attention to a particular condition or fact, or give

information on a subject.

• Warnings caution you about conditions which can result in serious

injury or death and/or damage to the equipment. They also tell you
how to avoid the danger. The warning symbols are used as follows:

Dangerous voltage warning

warns of high voltage which can cause

physical injury and/or damage to the equipment.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

«
1
2
3
4
...
»

Содержание OTAC-01




















Отзывы:

Нет отзывов

Похожие инструкции для OTAC-01

Бренд: Danfoss Страницы: 68

Бренд: Patton electronics Страницы: 9

Бренд: TAD Страницы: 128

Бренд: Baldor Страницы: 55

Бренд: INTECNO Страницы: 16

Бренд: GME Страницы: 21

Бренд: Harman Kardon Страницы: 16

Бренд: KanexPro Страницы: 32

Бренд: FOLSOM Страницы: 61

Бренд: Brook Страницы: 43

Бренд: Sincro Страницы: 84

Бренд: Yarvik Страницы: 64

Бренд: MAKINEX Страницы: 24

EQUINOX BATT EQX2 BATT

Бренд: Salicru Страницы: 40

Бренд: RoboGuard Страницы: 2

DT-IPTV-QAM-ASI-2H

Бренд: Data-Tronix Страницы: 30

Бренд: Conergy Страницы: 384

Бренд: GE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды