ABB OTAC-01 Скачать руководство пользователя страница 14

Страница: 14 / 19

Start-Up

Encoder

This group defines the setup for encoder use:

• Set the number of encoder pulses per shaft revolution.

• Enable the encoder operation.

• Defines how mechanical angle and revolution data is reset.

Note!

a check under the heading “S” indicates that the parameter can

only be modified when the drive is stopped.

Group 50: Encoder

Code Description Range

Resolution

Default

5001

PULSE NR

0…16384 ppr

1024

Sets the number of pulses provided by an optional encoder for each full motor shaft revolution.

5002

ENCODER ENABLE

0, 1

Enables/disables optional external encoder.
0 =

DISABLE

– Drive uses speed feedback derived from the internal motor model (applies for

any setting of parameter 9904

MOTOR

CTRL

MODE

1 =

ENABLE

– Drive uses feedback from an optional encoder. This function requires the Pulse

Encoder Interface Module (OTAC-01) and an encoder. Operation depends on the setting of
parameter 9904

MOTOR

CTRL

MODE

• 9904 = 1 (

VECTOR

SPEED

), the encoder provides improved speed feedback and improved

low speed torque accuracy.

• 9904 = 2 (

VECTOR

TORQ

), the encoder provides improved speed feedback and improved

low speed torque accuracy.

• 9904 = 3 (

SCALAR

SPEED

), the encoder provides speed feedback. (This is not closed loop

speed regulation. However, using parameter 2608

SLIP

COMP

RATIO

and an encoder

improves steady state speed accuracy.)

5003

ENCODER FAULT

1, 2

Defines the drive response if the encoder signal is lost.
1 =

FAULT

– A fault is generated, and the motor coasts to a stop.

2 =

WARNING

– An alarm is generated and the ACS550 operates as is if parameter 5002

ENCODER

ENABLE

= 0 (

DISABLE

), that is, speed feedback is derived from the internal motor

model.

5010

Z PLS ENABLE

0, 1

Enables/disables the use of an encoder’s Z-pulse to define the motor shaft’s zero position.
When enabled, a Z-pulse input resets parameter 0146

MECH

ANGLE

to zero to define the shaft’s

zero position. This function requires an encoder that provides Z-pulse signals.
0 =

DISABLE

– Z-pulse input is not present or ignored if present.

1 =

ENABLE

– A Z-pulse input resets parameter 0146

MECH

ANGLE

to zero.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание OTAC-01




















Результаты поиска

Содержание OTAC-01

Отзывы:

Похожие инструкции для OTAC-01

Бренды по названию

Популярные бренды

ABB OTAC-01, Руководство пользователя

Результаты поиска

Содержание OTAC-01

Отзывы:

Похожие инструкции для OTAC-01

Бренды по названию

Популярные бренды