ABB OTAC-01 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 19

background image

5

Installation

Installing the Module

Delivery Check

The OTAC-01 module package contains:

• OTAC-01 module

• Warning stickers in several languages

• This manual

Mounting

WARNING!

Follow the safety instructions given in this guide and in the

ACS550 User’s Manual.

To mount the OTAC-01 module:

1. If not already off, remove mains power from the drive.

2. Remove the drive cover. (See instructions in the drive User’s Manual.)

3. Insert the OTAC-01 module’s

plastic hooks into the front of
the drive at SLOT 1.

4. Carefully fit the connector at

the other end of the module
into the drive connector.

5. Press until the retaining clip

locks the module into position.

NOTE!

Signal and power

connections to the drive are
automatically made through a
6-pin connector.

6. Connect the ground lead to

the chassis screw terminal on the drive.

3

4

5

7

6

X0062

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

«
...
3
4
5
6
7
...
»

Содержание OTAC-01




















Отзывы:

Нет отзывов

Похожие инструкции для OTAC-01

Бренд: ABB Страницы: 62

LaCinema Mini HD Connect

Бренд: LaCie Страницы: 74

Бренд: C&C TECHNIC Страницы: 2

Бренд: Lika Страницы: 2

Бренд: Vacon Страницы: 102

HYT-10.0HV-EUG1

Бренд: Hoymiles Страницы: 34

Бренд: 3onedata Страницы: 2

Бренд: NANO MACHINES Страницы: 5

Бренд: Beckhoff Страницы: 40

Бренд: Ensemble Designs Страницы: 27

Бренд: CEL-MAR Страницы: 16

Бренд: Phoenix Contact Страницы: 34

Бренд: V-TAC Страницы: 32

BrightSign MH6-HD

Бренд: Audio Authority Страницы: 8

Бренд: Sollae Systems Страницы: 70

Бренд: Duracell Страницы: 37

Бренд: Woxcon Страницы: 23

Бренд: Conceptronic Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды