ABB IRB 140 Скачать руководство пользователя страница 179

Страница: 179 / 252

Note

Action

Connectors:

•

R3.MP1

•

R3.FB1

Disconnect the motor 1 connectors inside the con-
sole.

Cut any cable ties and remove any brackets securing
the cables.

Shown in the figure

Location of

motor axis 1 on page 177

Remove the cable gland by removing its

attachment

screws

, and pull the cables out from the console.

Connect to connector R3.MP1

•

+: pin 7

•

-: pin 8

In order to release the brakes, connect the 24 VDC
power supply:

Shown in the figure

Location of

motor axis 1 on page 177

Remove the motor by unscrewing its four

attachment

screws

and plain washers.

Lift the motor to get the pinion away from the gear
and disconnect the brake release voltage.

Remove the motor by gently lifting it straight up.

Refitting

The procedure below details how to refit motor, axis 1.

WARNING

Please observe the following before doing any repair work on the manipulator:

•

Motors and gears are HOT after running the robot! Touching the motors and
gears may result in burns!

•

Turn off all electric power, hydraulic, and pneumatic pressure supplies to
the robot!

•

Take any necessary measures to ensure that the manipulator does not
collapse as parts are removed, for example secure the lower arm with fixtures
if removing motor, axis 2.

Note

Whenever parting/mating motor and gearbox, the gears may be damaged if
excessive force is used!

Note

Action

Clean the joints that have been opened. See

Cut

the paint or surface on the robot before replacing
parts on page 118

Make sure the mating surfaces on the motor and
the gearbox are clean and free from burrs.

Art. no. is specified in section

Re-

quired equipment on page 177

Make sure the

o-ring

on the circumference of the

motor is seated properly. Lightly lubricate the

ring

with

grease

Connect to connector R2.MP1

•

+: pin 7

•

-: pin 8

In order to release the brake, connect the 24 VDC
power supply:

Continues on next page

Product manual - IRB 140

179

3HAC027400-001 Revision: V

4 Repair

4.7.1 Replacement of motor, axis 1

Continued

Содержание IRB 140





























































































































































































































































Результаты поиска

Содержание IRB 140

Отзывы:

ABB IRB 140, Руководство по эксплуатации продукта, Страница: 179 / 252

Результаты поиска

Содержание IRB 140

Отзывы: