ABB HT608780 Скачать руководство пользователя

Страница: 105 / 172

Operation Manual / Power2 850-M / 4.1 Low-pressure stage

4 Disassembly and assembly / 4.8 Removing the compressor casing

HZTL4062_EN

Rev.C

July 2020

7. Secure lifting gear to swivel lifting eye (90231).

8. Remove nut (72004) and carefully move out wall insert.

Fig. 9: Removing wall insert 3

9. Fit support angle (90480) with screws (90955) and nut (90415).

10. Put down the wall insert (77000).

11. Remove plate (90032), screw (90656), nut (90432) and plates (90031).

Remove lifting gear and bracket (90030).

12. Remove O-rings (77040 / 79020 / 79021).

13. Loosen screws (77016) and remove diffuser (79000).

4.8

Removing the compressor casing

Fig. 10: Removing the compressor casing 1

1. Loosen two studs (72002) and screw (72021) in the upper area.

2. Fit bracket (90030) with four screws (90959).

Page

Содержание HT608780











































































































































































Результаты поиска

Содержание HT608780

Отзывы:

Похожие инструкции для HT608780

Бренды по названию

Популярные бренды

ABB HT608780, Руководство по эксплуатации

Результаты поиска

Содержание HT608780

Отзывы:

Похожие инструкции для HT608780

Бренды по названию

Популярные бренды