ABB HT608780 Скачать руководство пользователя | Manualshive

Страница: 18 / 172

background image

Operation Manual / Power2 800-M / 2 Safety

1 Safety / 1.9 Periodic check of the pressure vessels

© Copyright 2019 ABB. All rights reserved.

HZTL4025_EN

Rev.B

November 2019

Explanations of the rating plate

The recommended replacement intervals and the corresponding operating limits are jointly
defined with the enginebuilder. This information is specific to the system.

The operating limits of the low-pressure stage are generally different from the operating
limits of the high-pressure stage.

Operation above the indicated values n

Bmax

, t

Bmax

can considerably shorten the recommended

replacement intervals. In such cases ABB recommends contacting the nearest ABB Tur-
bocharging Service Station.

n

Mmax

, t

Mmax

normally apply only when running at overload (110%) during trials on the engine

test bed. These limit values can also be permitted during operation for special applications.
Operation above n

Mmax

and t

Mmax

is not permitted.

Non-observance of the recommended replacement intervals increases the risk of unpredict-
able component failures.

Locations of the rating plates

The locations of the rating plates are defined in the Operation Manual, Chapter 4 Product
description.

1.9

Periodic check of the pressure vessels

The pressure vessels used by ABB Turbocharging, such as those for wet or dry cleaning, are
so-called "simple pressure vessels".

¡

The locally applicable legal regulations regarding periodic checks of the pressure vessels
must be observed.

¡

The operating company is responsible for the safe operation of the pressure vessel.

WARNING

Danger due to pressure vessels

The operating company must make sure the pressure vessels are in proper
working condition and monitor them. Necessary repair or maintenance work
must be performed promptly, and the required safety measures must be
taken.

u

Pressure equipment must not be operated if defects are present.

Page

8

/

17

«
...
16
17
18
19
20
...
»

Содержание HT608780













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT608780

Бренд: ABB Страницы: 86

Бренд: DARAY Страницы: 28

Бренд: MacDon Страницы: 88

Бренд: Jiffy Страницы: 15

Бренд: Fisher Scientific Страницы: 42

Бренд: Badger Meter Страницы: 16

Sonopuls HD 4050

Бренд: BANDELIN Страницы: 48

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

Бренд: dbx Страницы: 12

Бренд: dbx Страницы: 13

Бренд: dbx Страницы: 72

Бренд: dbx Страницы: 11

Бренд: dbx Страницы: 16

Бренд: Hakko Electronics Страницы: 8

Professional HS 8

Бренд: Hailo Страницы: 5

Бренд: Hainbuch Страницы: 52

Бренд: IBEX Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды