ABB HT608780 Скачать руководство пользователя

Страница: 107 / 172

Operation Manual / Power2 850-M / 4.1 Low-pressure stage

4 Disassembly and assembly / 4.9 Removing the cartridge group

HZTL4062_EN

Rev.C

July 2020

Fig. 12: Moving out cartridge group 1

1. Remove the O-ring (42012).

2. Loosen and remove the screws (42087).

3. Fit swivel lifting eye (90231) to bracket (90030) and screw bracket to cartridge group

with two screws (90955).

4. Fit five plates (90031) and secure with plate (90032), screw (90656) and nut (90432).

5. Secure lifting gear to swivel lifting eye (90231) and secure cartridge group to crane.

6. Evenly press off cartridge group by screwing three press-off screws (90920) into the des-

ignated holes.

Fig. 13: Moving out cartridge group 2

7. Carefully move out cartridge group.

8. Put cartridge group into the fixtures in the turned-over toolbox cover.

9. Remove plate (90032), screw (90656), nut (90432) and plates (90031).

10. Remove the press-off screws (90920).

11. Remove O-rings (42017 / 42018).

Page

Содержание HT608780











































































































































































Результаты поиска

Содержание HT608780

Отзывы:

Похожие инструкции для HT608780

Бренды по названию

Популярные бренды

ABB HT608780, Руководство по эксплуатации

Результаты поиска

Содержание HT608780

Отзывы:

Похожие инструкции для HT608780

Бренды по названию

Популярные бренды