ABB Aztec 600 Color Скачать руководство пользователя страница 74

Страница: 74 / 110

Aztec 600 aluminium, ammonia, color, iron, manganese, phosphate

Single- and multi-stream colorimetric analyzers

13 Maintenance

IM/AZT6CR–EN Rev. R

7. Referring to Fig. 13.14, remove the four screws

and

remove the motor and sample tube

from the lower half

of the measuring cell.

8. Referring to Fig. 13.15:

a. Slide the sample tube

off the piston assembly

. Discard the sample tube.

b. Loosen retaining grub screw

, unscrew the

piston assembly

from the piston shaft

and

discard the piston assembly.

c. Remove O-ring

from the base of the motor

mounting plate and discard.

d. Fit new O-ring

ensuring it is located correctly in

the groove in the base of the motor mounting plate.

e. Screw the new piston

and sample tube

assembly onto piston shaft

and tighten the

retaining grub screw

f. Slide sample tube

up to contact O-ring

Fig. 13.14 Removing the Motor and Sample Tube

Fig. 13.15 Dismantling/Reassembling the Piston

Содержание Aztec 600 Color















































































































Результаты поиска

Содержание Aztec 600 Color

Отзывы:

ABB Aztec 600 Color, Руководство пользователя, Страница: 74 / 110

Результаты поиска

Содержание Aztec 600 Color

Отзывы: