ABB Aztec 600 Color Скачать руководство пользователя страница 60

Страница: 60 / 110

Aztec 600 aluminium, ammonia, color, iron, manganese, phosphate

Single- and multi-stream colorimetric analyzers

12 Diagnostic Information and Icons

IM/AZT6CR–EN Rev. R

Flow Failure, Stream n

The analyzer can not detect any sample in stream 'n'.

The indicated stream is excluded from the sampling sequence until the
analyzer has detected that sample has returned.

If there is sufficient flow to the analyzer:

1. Check that float is located in the side sample pot and is

unrestricted.

2. Check that end cap of the side sample pot is sufficiently placed to

allow the magnetic float to be within the area of operation of the
reed switch.

3. Check that the float switch lead is connected correctly to the

interconnection board.

4. Check that the magnetic read switch is operating correctly.

OFF

Flushing

The analyzer is in flushing mode.

This facility carries out a continuous routine but does not store or display
measurement values.

The routine can be used without a prior calibration and is useful when a
analyzer is swapped from one parameter to another.

The analyzer remains in flushing mode until it is stopped.

OFF

Head Comms Failure

Communication failure with Head Control Module.

1. Check that the head chip is inserted correctly.

2. Contact the local ABB representative.

OFF

Heating Failure

The analyzer has failed to reach operating temperature.

This alarm is initiated if the analyzer temperature fails to rise 0.2 °C (32 °F)

within 2 minutes during the temperature stabilizing routine.

1. Check the integrity of the ribbon cable connecting measurement

head to the interconnection board.

2. Contact the local ABB representative

OFF

Internal Communications Failed

Communication failure between the main board and the display
assembly.

1. Check the ribbon cable connection to the main board.

2. Contact the local ABB representative

–

Icon

Diagnostic message

Stop

Relay

Attention

Relay

Calibration

Relay

Failure

Relay

Table 12.1 Diagnostic Information, Relay Operations and Inhibits (Sheet 3 of 5)

Содержание Aztec 600 Color















































































































Результаты поиска

Содержание Aztec 600 Color

Отзывы:

ABB Aztec 600 Color, Руководство пользователя, Страница: 60 / 110

Результаты поиска

Содержание Aztec 600 Color

Отзывы: