manualshive.com logo in svg

ABB Aztec 600 Color, Руководство пользователя, Страница: 61 / 110

Поделиться
Скачать
ABB Aztec 600 Color Скачать руководство пользователя страница 61

Aztec 600 aluminium, ammonia, color, iron, manganese, phosphate 

Single- and multi-stream colorimetric analyzers

12 Diagnostic Information and Icons

IM/AZT6CR–EN Rev. R

59

Internal Electronics Temperature Too High/Low

The internal temperature of the electronics enclosure is either too high or 
too low.

1. Check that the ambient temperature limits have not been 

exceeded.

2. Contact the local ABB representative

OFF

OFF

OFF

ON

LED Failure

This alarm is initiated if the LED failed to adjust the detector voltage at the 
beginning of a calibration routine or, if during the piston reset routine, no 
light was sensed in the measurement cell even though the LED current is 
OK.

Check that the LED and detector are connected correctly and 
working.

OFF

OFF

OFF

ON

No Light at Detector

This alarm is initiated during the piston reset routine if, after moving up 
and down twice, the measurement cell is continuously dark and no LED 
or motor fault is detected.

1. Check that the LED and detector are connected correctly and 

working.

2. Check the measurement cell and piston.

OFF

OFF

OFF

ON

No Valid Calibration

There is no valid calibration stored within the analyzer memory.

Calibrate the analyzer.

ON

OFF

OFF

OFF

Non-Volatile Memory Error

This message appears if there is a problem with either the display 
electronics or the main board memory.

Power the analyzer down, wait for 10 seconds and power-up 
again. 

If the error still exists contact the local ABB representative

OFF

OFF

OFF

ON

Override Mode

The analyzer is in Override Mode. 

Normal running has been overridden by the operator. 

The Override Mode is useful to check analyzer operation manually.

The analyzer remains in Override Mode until it is stopped.

ON

OFF

OFF

OFF

Icon

Diagnostic message

Stop

Relay

Attention 

Relay

Calibration 

Relay

Failure 

Relay

Table 12.1 Diagnostic Information, Relay Operations and Inhibits (Sheet 4 of 5)

Содержание Aztec 600 Color















































































































Отзывы:

Нет отзывов