ABB ACS880 Series Скачать руководство пользователя страница 47

Страница: 47 / 50

Fault tracing 43

Fault tracing

About this chapter

This chapter lists all the warning and fault messages including possible causes and
corrective actions for the Centrifuge Decanter drive.

For the complete list of warning and fault messages, see

ACS880 primary control program

firmware manual (3AUA0000085967[English])

Warning messages

Note:

The list also contains events that appear in the Event log.

Code
(hex)

Warning

Cause

What to do

E200

Pre wash time
too long

Pre wash speed is higher
than fill speed.

Decrease pre wash time or
prewash speed.
See parameters,

and

E201

Wash time too
long

Wash speed is higher than
spin speed.

Decrease wash time or wash
speed.
See parameters

and

E202

Speed feedback
not inside range

Actual speed is beyond the
minimum and maximum
speed limits.

Increase the deceleration time
from spinning speed to unloading
speed or the deceleration time
from unload speed to stop at zero
speed.
See parameters

and

Содержание ACS880 Series



















































Результаты поиска

Содержание ACS880 Series

Отзывы:

Бренды по названию

Популярные бренды

ABB ACS880 Series, Инструкция к добавке

Результаты поиска

Содержание ACS880 Series

Отзывы:

Бренды по названию

Популярные бренды