ABB ACS180-04S-03A7-1 Скачать руководство пользователя страница 65

Страница: 65 / 192

the product variant. Before you connect the drive to the input power, examine the
screws and do the necessary actions shown in the table.

When to remove EMC screw or VAR screw

Screw material

Screw
label

IT systems (un-

grounded or high-

resistance groun-

ded) (C)

Corner-grounded

delta (B1), mid-

point-grounded

delta (B2) and

TT (D) systems

Symmetrically

grounded TN-S sys-

tems, i.e, center-

grounded wye (A)

Remove

Do not remove

Metal

EMC

Do not remove

Plastic

Remove

Do not remove

Metal

VAR

Do not remove

Plastic

L1
L2
L3
N
PE

L1
L2
L3

L1
L2
L3
N

1) Can install the metal screw included in the drive delivery to connect the internal EMC filter.
2) Not all ACS180 has VAR screw.

Note: ACS180-04N-...-4 drives do not support corner-grounded delta (B1) system.

For the locations of the screws, refer to

Disconnecting the EMC filter (page 66)

Electrical installation 65

Содержание ACS180-04S-03A7-1
































































































































































































Результаты поиска

Содержание ACS180-04S-03A7-1

Отзывы:

ABB ACS180-04S-03A7-1, Руководство по оборудованию, Страница: 65 / 192

Результаты поиска

Содержание ACS180-04S-03A7-1

Отзывы: