ABB ACS180-04S-03A7-1 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 192

ABB ACS180-04S-03A7-1 Скачать руководство пользователя страница 21

Introduction to the manual

Contents of this chapter

The chapter describes the applicability, target audience and purpose of the manual.
The chapter contains a list of related manuals and a flowchart for installation and
commissioning.

Applicability

This manual is applicable to ACS180 drives.

Target audience

This manual is intended for people who plan the installation, install, commission
and do maintenance work on the drive, or create instructions for the end user of
the drive concerning the installation and maintenance of the drive.

Read the manual before you work on the drive. You are expected to know the
fundamentals of electricity, wiring, electrical components and electrical schematic
symbols.

Categorization by frame size

The drives are manufactured in frame sizes (for example, R1). The information that
is applicable only to specific frames is identified with the frame size. The frame
size is shown on the type designation label.

2

Introduction to the manual 21

«
...
19
20
21
22
23
...
»

Содержание ACS180-04S-03A7-1

































































































































































































Отзывы:

Нет отзывов