ABB ACS180-04S-03A7-1 Скачать руководство пользователя страница 135

Страница: 135 / 192

Protection classes

IP20. The drive must be installed in a cabinet to fulfill the require-
ments for shielding from contact.

Degree of protection
(IEC/EN 60529)

UL open type. For indoor use only.

Enclosure types
(UL 61800-5-1)

lll

Overvoltage category
(IEC 60664-1)

Protective classes
(IEC/EN 61800-5-1)

Ambient conditions

Environmental limits for the drive are given below. The drive must be used in a
heated indoor controlled environment.

Transportation in
the protective
package

Storage in the
protective pack-
age

Operation installed for sta-
tionary use

Requirement

0 … 1000 m above sea level
without derating.

Installation site alti-
tude

1000 … 2000 m above sea
level with derating.

Technical data 135

Содержание ACS180-04S-03A7-1
































































































































































































Результаты поиска

Содержание ACS180-04S-03A7-1

Отзывы:

ABB ACS180-04S-03A7-1, Руководство по оборудованию, Страница: 135 / 192

Результаты поиска

Содержание ACS180-04S-03A7-1

Отзывы: