manualshive.com logo in svg

ABB ACS 600 Series, Руководство по оборудованию

Поделиться
Скачать
ABB ACS 600 Series Скачать руководство пользователя страница 28

Chapter 3 – Electrical Installation

3-6

ACx=ACS/ACC/ACP

ACS/ACC/ACP 604/607 Drives

Wiring Connections

WARNING!

 This work should only be carried out by a qualified 

electrician. The Safety Instructions on the first pages of this manual 
must be followed. Negligence of these instructions can cause injury or 
death. 

ACx 607

The input power and motor cables connect to the ACx 607 in the left 
part of the cabinet. Input power, motor and control cable entry is from 
below or from above as specified at time of order and indicated by the 
Type Code.  Refer to 

Appendix B for additional information and 

drawings showing cable entry and terminal locations. 

To connect the input power, motor and control cables, carry out the 
following procedure.

WARNING!

 Make sure that the ACx 607 is disconnected from the 

power during installation. Wait for 5 minutes if the ACx 607 is already 
connected to the mains after disconnecting mains power. 

Wiring Access

1. Open the cabinet door. 

2. Open the hinged assembly plate to gain access to the input power 

and motor cable terminals.

3. Measure the voltage between each input terminal (U1, V1, W1) 

and ground with a multimeter (impedance at least 1 M

Ω

) to 

ensure that the drive is discharged.

Conduit Plate

The External Filter Type Code 8 (20th digit of the Type Code) identifies 
drives equipped with blank conduit plates shown in the dimensional 
drawings in Appendix B. The following installation procedure applies to 
installations utilizing conduit. For CE installation, refer to Appendix C.

Attach conduits to the conduit entry plates at the top and/or bottom of 
the drive. Conduit plate sizes and locations and terminal locations are 
shown on the dimensional drawings in Appendix B. Terminal wire size 
capacities are listed on page __ in Appendix A. Select locations for 
input power, motor, brake resister and control conduits according to 
terminal locations and size requirements. Pull the wires and cables 
through the conduits into the enclosure.

Содержание ACS 600 Series



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды