abaco systems PCI-5565PIORC Скачать руководство пользователя

Страница: 33 / 66

Publication No. 500-9367855565-000 Rev. D.0

Programming 33

Table 3-3 PCI Command Register

PCI Command: Offset $04

Bit

Description

Read

Write

*Value after

PCI Reset

I/O Space.

Writing a one (1) allows the device to respond to I/O

Space accesses.

Writing a zero (0) disables the device from

responding to I/O Space accesses.

Yes

Memory Space

Writing a one (1) allows device to respond to

Memory Space accesses.

Writing a zero (0) disables the device from

responding to Memory Space accesses.

Yes

Master Enable.

Writing a one (1) allows the device to behave as a

bus master.

Writing a zero (0) disables the device from

generating bus master accesses.

Yes

Special Cycle.

Not Supported

Yes

Reserved

N/A

VGA Palette Snoop

Not Supported

Yes

Parity Error Response.

Writing a zero (0) indicates parity error is ignored

and the operation continues.

Writing a one (1) indicates parity checking is

enabled.

Yes

Wait Cycle Control.

Controls whether a device does address/data

stepping.

A zero (0) indicates the device never does stepping.

A one (1) indicates the device always does stepping.

(NOTE: Hardwired to zero (0).)

Yes

SERR# Enable.

Writing a one (1) enables SERR# driver.

Writing a zero (0) disables SERR# driver.

Yes

Reserved

N/A

Interrupt Disable:

When set (1), this bit disables the Reflective Memory

from asserting its interrupt pin.

When not set (0), interrupts are generated normally.

Yes

15:11

Reserved

Yes

NOTE:

This register will be altered by the system BIOS during the system boot process (e.g., $0107).

Содержание PCI-5565PIORC



































































Результаты поиска

Содержание PCI-5565PIORC

Отзывы:

Похожие инструкции для PCI-5565PIORC

Бренды по названию

Популярные бренды

abaco systems PCI-5565PIORC, Справочник по аппаратуре

Результаты поиска

Содержание PCI-5565PIORC

Отзывы:

Похожие инструкции для PCI-5565PIORC

Бренды по названию

Популярные бренды