abaco systems PCI-5565PIORC страница 40 Скачать руководство пользователя

Страница: 40 / 66

40 PCI-5565PIORC* Ultrahigh Speed Fiber-Optic Reflective Memory with Interrupts

Publication No. 500-9367855565-000 Rev. D.0

NOTE

The RFM-5565 does not support the optional Power Management, Hot Swap and Vital features of the

Table 3-21 PCI Capability Pointer Register

Capability Pointer: Offset $34

Bit

Description

Read Write Value after

PCI Reset

7:0

New Capability Pointer.

Offset into PCI Configuration Space for

the location of the first item in the New Capabilities Linked List.

Yes

$78

31:8

Reserved

Yes

Table 3-22 PCI Interrupt Line

PCI Interrupt Line: PCIILR, Offset $3C

Bit

Description

Read

Write

*Value after

PCI Reset

7:0

Interrupt Line Routing Value.

Value indicates which input of

the system interrupt controller(s) is connected to each

interrupt line of the device.

Yes

NOTE:

This register will be altered by the system BIOS during the system boot process.

Table 3-23 PCI Interrupt Pin

PCI Interrupt Pin: PCIIPR, Offset $3D

Bit

Description

Read

Write

Value after

PCI Reset

7:0

Interrupt Pin Register.

Indicates which interrupt

pin the device uses. The following values are

decoded (the Reflective Memory supports only

INTA#).

1 = INTA#

2 = INTB#

3 = INTC#

4 = INTD#

Yes

Table 3-24 PCI Min_Gnt

PCI Min_Gnt: PCIMGR, Offset $3E

Bit

Description

Read

Write

Value after

PCI Reset

7:0

Min_Gnt.

Specifies how long a burst period a

device needs, assuming a clock rate of 33 MHz.

Value is a multiple of ¼

sec increments.

Yes

Table 3-25 PCI Max_Lat

PCI Max_Lat: PCIMLR, Offset $3F

Bit

Description

Read

Write

Value after

PCI Reset

7:0

Max_Lat.

Specifies how often the device must

gain access to the PCI bus. Value is a multiple of

sec increments.

Yes

Содержание PCI-5565PIORC



































































Результаты поиска

Содержание PCI-5565PIORC

Отзывы:

Похожие инструкции для PCI-5565PIORC

Бренды по названию

Популярные бренды

abaco systems PCI-5565PIORC, Справочник по аппаратуре

Результаты поиска

Содержание PCI-5565PIORC

Отзывы:

Похожие инструкции для PCI-5565PIORC

Бренды по названию

Популярные бренды