abaco systems PCI-5565PIORC Скачать руководство пользователя | Manualshive

Страница: 36 / 66

background image

36 PCI-5565PIORC* Ultrahigh Speed Fiber-Optic Reflective Memory with Interrupts

Publication No. 500-9367855565-000 Rev. D.0

PCI Base Address Register 0 contains the starting address for memory mapped
accesses to the Local Configuration Registers, which include the interrupt Control
and Status and the DMA Registers. The value in this register is loaded by the
system BIOS.

PCI Base Address Register 1 contains the starting address for I/O mapped
accesses to Local Configuration Registers. The value in this register is loaded by
the system BIOS.

Table 3-10 PCI Built-in Self Test Register

PCI Built-in Self Test: Offset $0F

Bit

Description

Read

Write

Value after

PCI Reset

3:0

BIST Pass/Failed.

Writing $0 indicates a device passed its test.

Non-$0 values indicate a device failed its test. Device-

specific failure codes can be encoded in a non-$0 value.

Yes

No

$0

5:4

Reserved.

Yes

No

00

6

PCI BIST Interrupt Enable.

The PCI bus writes a one (1)

to enable BIST, which generates an interrupt to the Local

bus. The Local bus resets this bit when BIST is complete.

The software should fail device if BIST is not complete

after two seconds. Refer to the Runtime registers for

interrupt Control and Status.

Yes

Yes

0

7

BIST Support.

Returns a one (1) if device supports BIST.

Returns a zero (0) if device is not BIST-compatible.

Yes

No

0

Table 3-11 PCI Base Address Register 0 for Access to Local Configuration Registers

PCIBAR0: Offset $10

Bit

Description

Read

Write

*Value after

PCI Reset

0

Memory Space

Indicator.

Writing zero (0) indicates the register maps into

Memory Space. Writing a one (1) indicates the register

maps into I/O Space. (

NOTE

: Hardcoded to zero (0).)

Yes

No

0

2:1

Register Location.

Values:

00 - Locate anywhere in 32-bit Memory Address Space.

01 - Locate below 1-MByte Memory Address Space.

10 - Locate anywhere in 64-bit Memory Address Space.

11 - Reserved

(

NOTE:

Hardcoded to 00.)

Yes

No

00

3

Prefetchable

. Writing a one (1) indicates there are no

side effects on reads. (

NOTE

: Hardcoded to zero (0).)

Yes

No

0

7:4

Memory Base Address

. Memory Base Address for

access to Local Configuration registers (requires 256

bytes).

(

NOTE

: Hardcoded to $0.)

Yes

No

$0

31:8

Memory Base Address

. Memory Base Address for

access to Local Configuration registers.

Yes

Yes

$0

*

NOTE:

This register will be altered by the system BIOS during the system boot process.

«
...
34
35
36
37
38
...
»

Содержание PCI-5565PIORC



































































Отзывы:

Нет отзывов

Похожие инструкции для PCI-5565PIORC

Бренд: U-Prox Страницы: 4

ImageMate SDDR-73

Бренд: SanDisk Страницы: 60

Бренд: Sunrich Tech Страницы: 11

Бренд: AUDIOLINE Страницы: 2

MIPort Universal PCI Cards 3PCIOU1

Бренд: B&B Electronics Страницы: 4

Бренд: TerraTec Страницы: 23

Radeon CrossFire

Бренд: ATI Technologies Страницы: 40

Бренд: Stealth Cam Страницы: 24

Бренд: Tvone Страницы: 68

Бренд: Planet Страницы: 41

Бренд: Digicom Страницы: 2

PSION WORKABOUT PRO

Бренд: TGM Страницы: 40

Linksys Wireless-B

Бренд: Cisco Страницы: 62

Linksys LNE100TX

Бренд: Cisco Страницы: 85

Intersil ISL38001C

Бренд: Conexant Страницы: 10

CDUOFWU Version 2.0

Бренд: Conceptronic Страницы: 25

Бренд: Acromag Страницы: 19

Бренд: Acorp Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды